Handling and Storage | Agilent Technologies 85032B/E 50 instruction

Use, Maintenance, and Care of the Devices

Handling and Storage

How to Separate a Connection

To avoid lateral (bending) force on the connector mating plane surfaces, always support the devices and connections.

CAUTION Turn the connector nut, not the device body. Major damage to the center conductor can occur if the device body is twisted.

1.Use an open-end wrench to prevent the device body from turning.

2.Use another open-end wrench to loosen the connector nut.

3.Complete the separation by hand, turning only the connector nut.

4.Pull the connectors straight apart without twisting, rocking, or bending either of the connectors.

Handling and Storage

•Install the protective end caps and store the calibration devices in the foam-lined storage case when not in use.

•Never store connectors loose in a box, desk, or bench drawer. This is the most common cause of connector damage during storage.

•Keep connectors clean.

•Do not touch mating plane surfaces. Natural skin oils and microscopic particles of dirt are easily transferred to a connector interface and are very difficult to remove.

•Do not set connectors contact-end down on a hard surface. The plating and the mating plane surfaces can be damaged if the interface comes in contact with any hard surface.

85032B/E

3-15

Image 31

Agilent Technologies 85032B/E 50 manual Handling and Storage, How to Separate a Connection

Contents

Agilent Part Number Print Date July User’s and Service Guide Documentation Warranty Contents Troubleshooting General Information Calibration Kit Overview Kit Contents Options Installation of the Calibration DefinitionsCalibration Definitions Adapters Incoming Inspection Serial Number Record for 85032B Recording the Device Serial NumbersSerial Number Record for 85032E Preventive Maintenance Clarifying the Sex of a Connector Specifications Parameter Limits Temperature-What to Watch Out ForEnvironmental Requirements Environmental Requirements Pin Depth Mechanical Characteristics Pin Depth Limit Supplemental Electrical Characteristics Electrical SpecificationsSupplemental Electrical Characteristics Electrical Specifications for 50Ω Type-N Devices Electrical Specifications 85032B/E Use, Maintenance, and Care of the Devices Electrostatic Discharge ESD Protection Setup Inspect the Mating Plane Surfaces What Causes Connector Wear?Visual Inspection Look for Obvious Defects and Damage First Inspect Female Connectors Cleaning ConnectorsUse Compressed Air or Nitrogen Reinspect Clean the Mating Plane Surfaces Connector Gage Accuracy Gaging Connectors Reading the Connector Gage When to Gage Connectors Gaging Male Type-N Connectors Gaging Procedures Gaging Male Type-N Connectors Gaging Female Type-N Connectors Gaging Female Type-N Connectors Preliminary Connection How to Make a ConnectionFinal Connection Using a Torque Wrench Connections Wrench Positions Connecting the Two-Piece Female Open Handling and Storage How to Separate a Connection Handling and Storage 85032B/E Performance Verification How Agilent Verifies the Devices in This Kit Introduction How Often to Recertify Where to Send a Kit for RecertificationRecertification Limited Recertification Option Recertification 85032B/E Troubleshooting Troubleshooting Flowchart Troubleshooting Process Contacting Agilent Returning a Kit or Device to Agilent Returning a Kit or Device to Agilent 85032B/E Replaceable Parts Calibration Kit Storage Case Protective End Caps for ConnectorsReplaceable Parts for the 85032B Calibration Kit Adapters included with Option 100b Replaceable Parts for the 85032B Calibration Kit Replaceable Parts for the 85032E Calibration Kit ESD Protective Devices Connector Cleaning SuppliesReplaceable Parts-Items Not Included in the Calibration Kit Wrenches Introduction 85032B/E Standard Definitions Table A-1 Standard Class Assignments Standard Class AssignmentsClass Standard Class Label Standard Class Blank FormTable A-2 Standard Class Assignments Blank Form Calibration Kit Label Class Nominal Standard Definitions Setting the System Impedance Min Max Table A-3 Standard DefinitionsSystem Z a = 50 Ω Calibration Kit Label Type 10C2× 10C3× Standardb Offset Freq Number Type 10C0× 10C1× PsDelayTable A-4 Standard Definitions Blank Form System Z 0 a = Index Index-2 85032B/E Index-3