Index-3 | Agilent Technologies 85032B/E 50 manual

Index

temperature, 2-2supplemental characteristics, 2-3supplemental electrical

characteristics, 2-5supplies

cleaning, 1-3system impedance

setting, A-4

T

tag

service, 1-4,4-3,5-3temperature

calibration, 2-2device, 2-2error-corrected temperature

range, 2-2

measurement, 2-2operating range, 2-2verification and measurement,

2-2

test data, 4-2threads

connector, 3-4torque wrench, 1-3,3-12

part number, 6-5specifications, 3-12

traceability, 4-2troubleshooting, 5-2two-piece female open, 3-14

V

verification performance, 4-2temperature, 2-2

visual inspection, 3-3

W

warranty, documentation, ii wrench

open-end,1-3,3-15part number, 6-5undoing connections, 3-15

torque, 1-3

part number, 6-5wrenches

part numbers, 6-5

Z

zeroing

connector gage, 3-8,3-10zeroing connector gage, 3-8,

3-10

85032B/E

Index-3

Image 55

Agilent Technologies 85032B/E 50 manual Index-3

Contents

Agilent Part Number Print Date July User’s and Service Guide Documentation Warranty Contents Troubleshooting General Information Calibration Kit Overview Kit Contents Options Installation of the Calibration DefinitionsCalibration Definitions Adapters Incoming Inspection Serial Number Record for 85032B Recording the Device Serial NumbersSerial Number Record for 85032E Preventive Maintenance Clarifying the Sex of a Connector Specifications Parameter Limits Temperature-What to Watch Out ForEnvironmental Requirements Environmental Requirements Pin Depth Mechanical Characteristics Pin Depth Limit Supplemental Electrical Characteristics Electrical SpecificationsSupplemental Electrical Characteristics Electrical Specifications for 50Ω Type-N Devices Electrical Specifications 85032B/E Use, Maintenance, and Care of the Devices Electrostatic Discharge ESD Protection Setup Inspect the Mating Plane Surfaces What Causes Connector Wear?Visual Inspection Look for Obvious Defects and Damage First Inspect Female Connectors Cleaning ConnectorsUse Compressed Air or Nitrogen Reinspect Clean the Mating Plane Surfaces Connector Gage Accuracy Gaging Connectors Reading the Connector Gage When to Gage Connectors Gaging Male Type-N Connectors Gaging Procedures Gaging Male Type-N Connectors Gaging Female Type-N Connectors Gaging Female Type-N Connectors Preliminary Connection How to Make a ConnectionFinal Connection Using a Torque Wrench Connections Wrench Positions Connecting the Two-Piece Female Open Handling and Storage How to Separate a Connection Handling and Storage 85032B/E Performance Verification How Agilent Verifies the Devices in This Kit Introduction How Often to Recertify Where to Send a Kit for RecertificationRecertification Limited Recertification Option Recertification 85032B/E Troubleshooting Troubleshooting Flowchart Troubleshooting Process Contacting Agilent Returning a Kit or Device to Agilent Returning a Kit or Device to Agilent 85032B/E Replaceable Parts Calibration Kit Storage Case Protective End Caps for ConnectorsReplaceable Parts for the 85032B Calibration Kit Adapters included with Option 100b Replaceable Parts for the 85032B Calibration Kit Replaceable Parts for the 85032E Calibration Kit ESD Protective Devices Connector Cleaning SuppliesReplaceable Parts-Items Not Included in the Calibration Kit Wrenches Introduction 85032B/E Standard Definitions Table A-1 Standard Class Assignments Standard Class AssignmentsClass Standard Class Label Standard Class Blank FormTable A-2 Standard Class Assignments Blank Form Calibration Kit Label Class Nominal Standard Definitions Setting the System Impedance Min Max Table A-3 Standard DefinitionsSystem Z a = 50 Ω Calibration Kit Label Type 10C2× 10C3× Standardb Offset Freq Number Type 10C0× 10C1× PsDelayTable A-4 Standard Definitions Blank Form System Z 0 a = Index Index-2 85032B/E Index-3