Contents | Agilent Technologies 85032B/E 50 specs

Contents

1. General Information
Calibration Kit Overview	1-2
Kit Contents	1-2
Broadband Loads	1-2
Opens and Shorts	1-2
Adapters	1-3
Calibration Definitions	1-3
Installation of the Calibration Definitions	1-3
Options	1-3
Equipment Required but Not Supplied	1-3
Incoming Inspection	1-4
Recording the Device Serial Numbers	1-5
Clarifying the Sex of a Connector	1-6
Preventive Maintenance	1-6

2. Specifications

Environmental Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-2

Temperature—What to Watch Out For . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-2

Mechanical Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-3

Pin Depth. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-3

Electrical Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-5

Certification. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-5

Supplemental Electrical Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-5

3. Use, Maintenance, and Care of the Devices
Electrostatic Discharge	.3-2
Visual Inspection	.3-3
Look for Obvious Defects and Damage First	.3-3
What Causes Connector Wear?	.3-3
Inspect the Mating Plane Surfaces	.3-3
Inspect Female Connectors	.3-4
Cleaning Connectors	.3-4
Gaging Connectors	.3-6
Connector Gage Accuracy	.3-6
When to Gage Connectors	.3-7
Reading the Connector Gage	.3-7
Gaging Procedures	.3-8
Gaging Male Type-N Connectors	.3-8
Gaging Female Type-N Connectors	3-10
Connections	3-12
How to Make a Connection	3-12
Preliminary Connection	3-12
Final Connection Using a Torque Wrench	3-12
Connecting and Disconnecting the Two-Piece Female Open (85032B)	3-14
How to Separate a Connection	3-15
Handling and Storage	3-15

85032B/E

iii

Image 3

Agilent Technologies 85032B/E 50 manual Contents

Contents

Agilent Part Number Print Date July User’s and Service Guide Documentation Warranty Contents Troubleshooting General Information Calibration Kit Overview Kit Contents Options Installation of the Calibration DefinitionsCalibration Definitions Adapters Incoming Inspection Recording the Device Serial Numbers Serial Number Record for 85032BSerial Number Record for 85032E Preventive Maintenance Clarifying the Sex of a Connector Specifications Parameter Limits Temperature-What to Watch Out ForEnvironmental Requirements Environmental Requirements Pin Depth Mechanical Characteristics Pin Depth Limit Supplemental Electrical Characteristics Electrical SpecificationsSupplemental Electrical Characteristics Electrical Specifications for 50Ω Type-N Devices Electrical Specifications 85032B/E Use, Maintenance, and Care of the Devices Electrostatic Discharge ESD Protection Setup Inspect the Mating Plane Surfaces What Causes Connector Wear?Visual Inspection Look for Obvious Defects and Damage First Cleaning Connectors Inspect Female ConnectorsUse Compressed Air or Nitrogen Reinspect Clean the Mating Plane Surfaces Connector Gage Accuracy Gaging Connectors Reading the Connector Gage When to Gage Connectors Gaging Male Type-N Connectors Gaging Procedures Gaging Male Type-N Connectors Gaging Female Type-N Connectors Gaging Female Type-N Connectors Preliminary Connection How to Make a ConnectionFinal Connection Using a Torque Wrench Connections Wrench Positions Connecting the Two-Piece Female Open Handling and Storage How to Separate a Connection Handling and Storage 85032B/E Performance Verification How Agilent Verifies the Devices in This Kit Introduction How Often to Recertify Where to Send a Kit for RecertificationRecertification Limited Recertification Option Recertification 85032B/E Troubleshooting Troubleshooting Flowchart Troubleshooting Process Contacting Agilent Returning a Kit or Device to Agilent Returning a Kit or Device to Agilent 85032B/E Replaceable Parts Calibration Kit Storage Case Protective End Caps for ConnectorsReplaceable Parts for the 85032B Calibration Kit Adapters included with Option 100b Replaceable Parts for the 85032B Calibration Kit Replaceable Parts for the 85032E Calibration Kit ESD Protective Devices Connector Cleaning SuppliesReplaceable Parts-Items Not Included in the Calibration Kit Wrenches Introduction 85032B/E Standard Definitions Standard Class Assignments Table A-1 Standard Class AssignmentsClass Standard Class Label Standard Class Blank FormTable A-2 Standard Class Assignments Blank Form Calibration Kit Label Class Nominal Standard Definitions Setting the System Impedance Min Max Table A-3 Standard DefinitionsSystem Z a = 50 Ω Calibration Kit Label Type 10C2× 10C3× Standardb Offset Freq Number Type 10C0× 10C1× PsDelayTable A-4 Standard Definitions Blank Form System Z 0 a = Index Index-2 85032B/E Index-3