Incoming Inspection | Agilent Technologies 85032B/E 50 specs

General Information

Incoming Inspection

Incoming Inspection

Verify that the shipment is complete by referring to Figure 6-1or Figure 6-2.

Check for damage. The foam-lined storage case provides protection during shipping.

If the case or any device appears damaged, or if the shipment is incomplete, contact Agilent. See Table 5-1 on page 5-3. Agilent will arrange for repair or replacement of incomplete or damaged shipments without waiting for a settlement from the transportation company.

When you send the kit or device to Agilent, include a service tag (found near the end of this manual) with the following information:

•your company name and address

•the name of a technical contact person within your company, and the person's complete phone number

•the model number and serial number of the kit

•the part number and serial number of the device

•the type of service required

•a detailed description of the problem

1-4

85032B/E

Image 8

Agilent Technologies 85032B/E 50 manual Incoming Inspection

Contents

User’s and Service Guide Agilent Part Number Print Date July Documentation Warranty Contents Troubleshooting General Information Kit Contents Calibration Kit Overview Installation of the Calibration Definitions Calibration DefinitionsAdapters Options Incoming Inspection Serial Number Record for 85032E Recording the Device Serial NumbersSerial Number Record for 85032B Clarifying the Sex of a Connector Preventive Maintenance Specifications Temperature-What to Watch Out For Environmental RequirementsEnvironmental Requirements Parameter Limits Mechanical Characteristics Pin Depth Pin Depth Limit Electrical Specifications Supplemental Electrical CharacteristicsElectrical Specifications for 50Ω Type-N Devices Supplemental Electrical Characteristics Electrical Specifications 85032B/E Use, Maintenance, and Care of the Devices ESD Protection Setup Electrostatic Discharge What Causes Connector Wear? Visual InspectionLook for Obvious Defects and Damage First Inspect the Mating Plane Surfaces Use Compressed Air or Nitrogen Cleaning ConnectorsInspect Female Connectors Clean the Mating Plane Surfaces Reinspect Gaging Connectors Connector Gage Accuracy When to Gage Connectors Reading the Connector Gage Gaging Procedures Gaging Male Type-N Connectors Gaging Male Type-N Connectors Gaging Female Type-N Connectors Gaging Female Type-N Connectors How to Make a Connection Final Connection Using a Torque WrenchConnections Preliminary Connection Wrench Positions Connecting the Two-Piece Female Open How to Separate a Connection Handling and Storage Handling and Storage 85032B/E Performance Verification Introduction How Agilent Verifies the Devices in This Kit Where to Send a Kit for Recertification RecertificationLimited Recertification Option How Often to Recertify Recertification 85032B/E Troubleshooting Troubleshooting Process Troubleshooting Flowchart Returning a Kit or Device to Agilent Contacting Agilent Returning a Kit or Device to Agilent 85032B/E Replaceable Parts Protective End Caps for Connectors Replaceable Parts for the 85032B Calibration KitAdapters included with Option 100b Calibration Kit Storage Case Replaceable Parts for the 85032B Calibration Kit Replaceable Parts for the 85032E Calibration Kit Connector Cleaning Supplies Replaceable Parts-Items Not Included in the Calibration KitWrenches ESD Protective Devices Introduction 85032B/E Standard Definitions Class Standard Class Label Standard Class AssignmentsTable A-1 Standard Class Assignments Blank Form Table A-2 Standard Class Assignments Blank FormCalibration Kit Label Class Standard Class Setting the System Impedance Nominal Standard Definitions Table A-3 Standard Definitions System Z a = 50 Ω Calibration Kit LabelType Min Max Standardb Offset Freq Number Type 10C0× 10C1× PsDelay Table A-4 Standard Definitions Blank FormSystem Z 0 a = 10C2× 10C3× Index Index-2 85032B/E Index-3