Important Safety Instructions | Akai Ewi4000s specs

IMPORTANT SAFETY INSTRUCTIONS

1.Before you operate the EWI4000s, read these instructions.

2.Keep these instructions.

3.Heed all warnings.

4.Follow all instructions.

5.Do not use this apparatus near water.

6.Clean only with a dry cloth.

7.Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.

8.Do not install near any heat sources such as radiators, heat register, stoves, or other apparatus (including amplifiers) that produce heat.

9.Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong is provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet. Where the mains plug or an appliance coupler is used as the disconnect device, the disconnect device shall remain readily operable.

10.Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus.

11.Only use attachment/accessories specified by the manufacturer.

12.Use only the cart, stand, tripod, bracket or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over.

13.Unplug this apparatus during lightning storms or when unused for long periods of time.

14.Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.

PORTABLE CART WARNING

S3125A

15.Do not expose this apparatus to dripping or splashing and ensure that no objects filled with liquids, such as vases, are placed on the apparatus.

16.Use only with the specified AC adapter.

1

Image 3

Akai Ewi4000s manual Important Safety Instructions, Portable Cart Warning

Contents

Reference Manual Page Portable Cart Warning Important Safety Instructions FCC Warning Table of Contents Introduction Features TOP Panel Parts & Functions Side / Rear Panel „ Glide Plate Section „ Program / Data Display Section „ Cable Clutch Section „ Bend Plate Section Power „ Using Battery Power„ AC adapter Connections „ Grounding Plates Basic OperationBasic Operation „ Note Keys „ Octave Shift Rollers „ Pitch Bend Plates „ Mouthpiece„ Vibrato „ Tonguing „ Hold Button and Octave Button Adjusting the Sensitivity of the Sensors „ Adjusting the Pitch Bend Sensors „ Adjusting the Breath Sensor „ Adjusting the Glide Sensor „ Adjusting the Vibrato Sensor „ a Note About Adjusting Your Sensors „ Adjusting the Touch Sensors Fingering Modes „ Assigning a Program Number to a Note Key Internal SoundProgram KEY Functions „ Selecting the Internal Sounds Program Key „ Recalling the Program Number Assigned to a Note Key „ Setting Program Change Preferences „ Program Down with the Octave Button „ Program Up with the Hold Button „ Adjusting the Reverb Volume Adjusting the Volumes„ Adjusting the Main Volume „ Adjusting the Volume of Each Program „ Adjusting the Reverb Effect Volume of Each Program „ Adjusting the Delay Effect Volume of Each Program„ Adjusting the Chorus Effect On/Off on Each Program „ Assigning Functions to the Octave Button Octave Button Functions Hold Button Functions „ Assigning Functions to the Hold Button „ Assigning Functions to the Glide Plate Pitch Bend Plate FunctionsGlide Plate Functions „ Assigning Functions to the Pitch Bend Plates „ Setting the Glide Effect Time & Rate Adjusting the KEY Delay Tuning Transpose Function Trans ButtonEditing the Internal Sound with Your Computer About Midi Transmitted Information from the EWI4000s Midi OUT„ Midi Program Change „ Changing the Breath Sensor Output „ Changing the Midi Channel „ Changing the Vibrato Sensor Output to Another Midi Event „ Setting the Midi Velocity Value „ Sending an All Notes Off Message „ Setting the Hold Function Hold Button on Midi Transmit„ Setting the Glide Plate Function on Midi Transmit „ Sending a Midi Panic Message to Reset All Controllers Level master Level preset Reverb master Restoring the Factory Presets „ The Left Hand Miscellaneous NotesEVI Fingerings „ The Right Hand „ Basic EVI Fingerings Software Updating Troubleshooting Octave Shift Rollers Fingering Charts EWI Fingerings Saxophone Fingerings Flute Fingerings Oboe Fingerings EVI Fingerings Transmit/Export Recognize/Import Remarks Midi Implementation Chart Octave Menu Structure Glide Parameter Range Defaults Update Control Protocol OFF Sound Module SpecificationsPage