Manuals / Allied Telesis / Computer Equipment / Switch

Allied Telesis AT-9900 Series manual Making Asynchronous Ports Respond More Quickly CR00011565

Models: AT-9900 Series

1 54

Page 42

Making Asynchronous Ports Respond More Quickly (CR00011565)

Figure 1: New parameters in the output of the show asyn=0 command

ASYN 0 : 0000001470 seconds	Last change at: 0000001465 seconds
ASYN information
Name	Asyn 0
Status	enabled
Mode	Ten
Data rate	9600
Parity	none
Data bits	8
Stop bits	1
Test mode	no
In flow state (mode)	on (Hardware)
Out flow state (mode)	off (Hardware)
Autobaud mode	disabled
Max tx queue length	16
TX queue length	3
Transmit frame	none
RX queue length	0
IP address	none
Max transmission unit	1500
Ten timer value	100
.
.
.

Version 276-03

C613-10474-00 REV B

Page 42

Image 42

Allied Telesis AT-9900 Series manual Making Asynchronous Ports Respond More Quickly CR00011565, Ten timer value

Contents

Software Maintenance Release Note for AT-8900 and AT-9900 series switchesVersion Enabling and Installing this Release LevelsEnabling and Installing this Release Enhancements Features inLevel LevelCR00011691 Features inLevel CR00011694CR00006475 LevelCR00000529 CR00007522CR00009201 CR00008699CR00008992 CR00009280CR00011128 CR00010886CR00011060 CR00011304CR00011411 CR00011349CR00011396 CR00011586CR00011780 CR00011665CR00011746 CR00011809CR00011991 CR00011855CR00011940 CR00011992CR00012096 CR00012013CR00012067 CR00012108CR00012204 CR00012140CR00012167 CR00012232CR00012304 CR00012319CR00012396 CR00012482 CR00012533Stacking CR00012613 CR00012649CR00012689 CR00008741 LevelCR00006900 CR00009379CR00010953 CR00010508CR00010952 CR00011105other parameters CR00011510outspi=spi other parameters CR00011659CR00011969 CR00011931CR00011943 CR00012014CR00012265 CR00012040CR00012175 CR00012283CR00012322 CR00012307CR00012314 CR00012329CR00012413 enable ospf debug=nrldisable ospf debug=nrl CR00012427Level CR00012594CR00003286 show log type=55 subtype=7 CR00011995show log type=55 subtype=backoff CR00012043enable mstp cist port=port-listall enable mstp port=port-listalldisable mstp port=port-listall enable mstp msti=instance port=port-listallCR00011271 “Securing a Single VLAN through Switch Filters CR00011271” on pageCR00011204 CR00011565set bridge stripvlantag=onoffyesnotruefalse CR00012620CR00012692 show bridgeLevel Features inNo level 1 issues LevelModule Module Module CR00011269 CR00011243ISAKMP CR00011300Module Level Level page For more information, see “Route Update Queue Length CR00010196” onEnhancements Assignments CR00011355” on pageAdding Static ARP Entries with Multicast MAC Addresses CR00011204 Adding Static ARP EntriesAccepting Packets with Conflicting Addresses To see whether macdisparity is enabled or disabled, use the command show ipVersion C613-10474-00 REV B vlansecure enabled Securing a Single VLAN through Switch Filters CR00011271Default behaviour vlansecure disabledConfiguring vlansecure Making Asynchronous Ports Respond More Quickly CR00011565 Figure 1 New parameters in the output of the show asyn=0 command Ten timer valueMaking Asynchronous Ports Respond More Quickly CR00011565 Displaying Routes Learned from a Specific BGP Peer CR00011724 Displaying the Number of Routes from a PeerDisplaying Information about the Routes from a Peer Memory Size Mbytes Route Update Queue Length CR00010196Default length number of entries Maximum possible length number of entriesParameter MeaningPermanent Assignments CR00011355 Setting up a Permanent AssignmentExample The commands to be executed on the router with address 172.20.34.9 are Syntax Command Referenceadd perm Descriptionadd perm reset perm set perm show perm Related Commandsdelete perm reset perm set perm show perm delete permRelated Commands reset permadd perm delete perm set perm show perm SyntaxRelated Commands delete perm reset perm show permset perm SyntaxDescription show permSyntax Examplesadd perm delete perm reset perm set perm Related CommandsVersion C613-10474-00 REV B