Features in 276-02

 

 

 

11

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

CR

Module

Level

Description

AR44x / AR450

AR7x5

AR750S

 

Rapier i

AT-8800

AT-8600

 

AT-8700XL

AT-8948

AT-9900

AT-9800

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

CR00012013

VLAN

2

When MLD snooping was enabled and the switch received IPv6 multicast packets

-

-

-

 

Y

Y

-

 

-

Y

Y

Y

 

 

 

(such as MLD Query, Report or Done messages; IPv6 NS packets; and IPv6 RA

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

packets) on a non-master port of a trunk group, it incorrectly forwarded them

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

out the master port. This resulted in a packet loop.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

This issue has been resolved.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

CR00012067

OSPF

2

A summary LSA was not turned into a route if the destination and mask fell inside

Y

Y

Y

 

Y

Y

Y

 

Y

Y

Y

Y

 

 

 

one of the router or switch’s active ranges, unless it exactly matched the active

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

range’s address and mask.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

This complied with RFC 1583 section 16.2. However, the recommended

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

behaviour has been modified in RFC 2328 section 16.2. To comply with this, the

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

LSA is now calculated if it falls inside one of the router or switch’s active ranges.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

CR00012096

Core, LLDP,

2

The LLDP module and several monitoring features started up when they were not

Y

-

-

 

-

-

-

 

-

-

-

-

 

Switch, Utility

 

needed. This impacted on performance.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

This issue has been resolved, and therefore performance has been improved,

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

especially for the AR440S router.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

CR00012108

Switch

2

The command disable switch port=port-numberlink=disable did not

-

-

-

 

-

-

-

 

-

-

Y

-

 

 

 

correctly disable the link for port 12 or 24 on AT-9924SP switches. It only disabled

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

ports 12 and 24 in software.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

This issue has been resolved.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

CR00012119

Load balancer

2

Previously, only one resstate trigger could be created for each load balancer

Y

Y

Y

 

Y

Y

-

 

-

Y

Y

Y

 

 

 

resource. This meant, for example, that you could create a trigger to activate a

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

script when a resource went down, but could not activate another script when

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

the resource came back up again.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

This issue has been resolved. You can now define different triggers to trigger off

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

each of the different states available for a given resource (such as lbstate=up

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

and lbstate=closing).

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Version 276-03

C613-10474-00 REV B

Page 11
Image 11
Allied Telesis AT-9900 Series manual Vlan, Switch, Utility, Command disable switch port=port-numberlink=disable did not