Alpine CDA-7878R Left Front + Speaker Output Lead White, ~ Right Front + Speaker Output Lead Grey

1	Antenna Receptacle	% Left Rear (–) Speaker Output Lead (Green/Black)
	Connect to the supplied ISO antenna convertor plug.	& Left Front (+) Speaker Output Lead (White)
2	Audio Interrupt In Lead (Pink/Black)	( Left Front (–) Speaker Output Lead (White/Black)
	Connect this lead to the Audio Interface output of a	) Right Front (–) Speaker Output Lead (Grey/Black)
	cellular phone which provides ground shorting when	~ Right Front (+) Speaker Output Lead (Grey)
	a call is received.	+ Right Rear (–) Speaker Output Lead (Violet/Black)
3	Remote Turn-On Lead (Blue/White)	, Right Rear (+) Speaker Output Lead (Violet)
	Connect this lead to the remote turn-on lead of your	- Front Output RCA Connectors
	amplifier or signal processor.	RED is right and WHITE is left.
4	Switched Power Lead (Ignition) (Red)	. Rear Output RCA Connectors
	Connect this lead to an open terminal on the vehicle’s	RED is right and WHITE is left.
	fuse box or another unused power source which	/ Subwoofer Output RCA Connectors
	provides (+) 12V only when the ignition is turned on	RED is right and WHITE is left.
	or in the accessory position.	: Ai-NET Cable (Included with CD Changer)
5	Power Antenna Lead (Blue)	; RCA Extension cable (Sold Separately)
	Connect this lead to the +B terminal of your power	< DC/DC Converter
	antenna, if applicable.	NOTES
	NOTE	• Do not install the converter at a location subjected to
	This lead should be used only for controlling the	water such as under the floor mat or air conditioner.
	vehicle's power antenna. Do not use this lead to turn on	This may cause a malfunction.
	an amplifier or a signal processor, etc.	• Do not bundle the DC/DC converter cable with other
6	Fuse Holder (15A)	audio cables. Doing so may induce noise into your
		system.
7	Battery Lead (Yellow)	• Keep the DC/DC converter away from the Antenna
	Connect this lead to the positive (+) post of the	cables and the rear side of the unit, otherwise noise
	vehicle's battery.	may be generated when receiving radio broadcast.
8	ISO Power Supply Connector	= Remote Control Interface Connector
9	Ground Lead (Black)
		To remote control interface box.
	Connect this lead to a good chassis ground on the
		> System Switch
	vehicle. Make sure the connection is made to bare
		When connecting a processor using Ai-NET, place
	metal and is securely fastened using the sheet metal
		this switch in the EQ/DIV position. When no device
	screw provided.
		is connected, leave the switch in the NORM position.
! Ai-NET Connector
		NOTE
	Connect this to the output or input connector of other
		Be sure to turn the power off to the unit before changing
	product (CD changer, Equalizer, etc.) equipped with
		the switch position.
	Ai-NET.
" Power Supply Connector		? Setting the 3WAY/2 WAY switch
# ISO Connector (Speaker Output)		Set the 3way/2way Switch according to your audio system.
$ Left Rear (+) Speaker Output Lead (Green)

The system whose frequency range is divided between the high frequency range and the low frequency range.

The system whose frequency range is divided among the high frequency range, mid frequency range, and the low frequency range.

The position of switching the switch: F/R/Sub-W				The position of switching the switch: 3WAY
Front high range			Front high range	High range			High range
				speaker (L)			speaker (R)
speaker (L)			speaker (R)
				Mid range			Mid range
Rear high range			Rear high range
				speaker (L)			speaker (R)
speaker (L)			speaker (R)	Low range		Low range
		Low range
Low range
				speaker (L)		speaker (R)
speaker (L)		speaker (R)
	Output of this unit :
			Front output	Rear output	SUB-W output

NOTES

•Use the SUB-W output cord to connect the unit to the Low Range speaker.

•You can use the built-in amplifier to output the Front output/Rear output.

•You cannot adjust the FADER when setting to 3 WAY.

45-EN