Setting the Treble Control (CDA-9812RX/CDA- 9811R only)
You can change the Treble Frequency emphasis to create your own tonal preference.
1 Press CENTER f to select the Treble (treble centre frequency) Control mode.
BASS → TREBLE → normal mode → BASS
10.0kHz ↔ 12.5kHz ↔ 15.0kHz ↔ 17.5kHz ↔ 10.0kHz
The displayed Treble frequency is emphasized.
Turn the Rotary encoder to select the desired treble level
You can emphasize the treble frequency.
•If no operation is performed within 15 seconds, the treble control setting will be turned off automatically.
•The treble level settings will be individually memorized for each source (FM, MW (LW), CD, etc.) until the setting is changed. The Treble frequency settings adjusted for one source are effective for all other sources (FM, MW (LW), CD, etc.).
•Depending on the connected devices, some functions and display indications do not work. However, treble level is still adjustable if an audio processor with the treble adjustment is connected.
•This function is inoperable when DEFEAT is set to ON.
•When you press DISP/B.OUT on the
Setting the Bass Type (CDA-9812RX/CDA- 9811R only)
This function allows for 3 different bass type settings. Select the one that appeals to you the most.
1 Press and hold CENTER f for at least 2 seconds to set the bass type.
2 Press g or f within 15 seconds to select the desired type (1 through 3).
TYPE 1 will sound best if you have a subwoofer in your system. Use TYPE 2 or 3 if you are using small diameter speakers.
3 Press and hold CENTER f for at least 2 seconds to return to normal mode.
•Bass centre frequency and bass band width previously set are replaced when selecting TYPE 1 through 3. When bass type is set to OFF, your previous settings are restored.
•Bass type is not selectable when connected to an external audio processor.
•When you press DISP/B.OUT on the
Adjusting the built-in Crossover (CDA-9812RX/CDA-9811R only)
The High and Low Pass Filters on this unit can be adjusted to suit your personal taste.
1 Press and hold
HPF - <Press momentarily> → LPF* - <Press momentarily>
→normal mode - <Press and hold for 2 seconds> → HPF
*When the subwoofer output of this unit is turned off, LPF and phase are deactivated.
2 Press g or f to select the desired setting.
HPF (Setting the High Pass Filter):
FLAT (OFF) ↔ 80Hz ↔ 120Hz ↔160Hz
All frequencies above the selected cutoff are output.
LPF(Setting the Low Pass Filter):
FLAT (OFF) ↔ 80Hz ↔ 120Hz ↔160Hz
All frequencies below the selected cutoff are output. (Only available when using the subwoofer output from this unit.)
•If no operation is performed within 15 seconds, the setup menu returns to normal mode.
•These functions are inoperative when an external,
•The Bass and Treble controls effectiveness in modifying the sound, depends on their settings and where the HPF and LPF are set.
•Except when the HPF and LPF is turned OFF, the subwoofer is in monaural mode.
•When the subwoofer is set to OFF, LPF mode and change of phase does not work.
Equalizer Presets (CDA-9815RB/CDA-9813R only)
3 typical equalizer settings are preset at the factory for a variety of musical source material.
1 Press EQ and select the EQ mode.
2 Press either g or f.
With each press of the button, the equalizer mode will display the selected equalizer characteristic.
FLAT(OFF) → POPS → ROCK → NEWS → FLAT(OFF)
FLAT : Flat frequency
POPS : Emphasize midrange
ROCK : Emphasize lows and highs
NEWS : Boost midrange and suppress highs and lows
Selecting directly
Select the desired button (1 through 4).
[1]: | FLAT(OFF) | [3]: ROCK |
[2]: | POPS | [4]: NEWS |
3 Press EQ to return to normal mode.
•This function is inoperable when DEFEAT is set to ON (page 17).
•EQ mode is automatically cancelled if no operation is performed within 15 seconds.
•When you press DISP/B.OUT, you can switch the Level Indicator display to the EQ Adjustment display. For details, see “Changing the Audio Level Display Pattern” (page 7).
