Alpine CDA-9853, CDA-9855 Adjusting and Storing the Crossover Settings, 2WAY System, 18-EN

Adjusting and Storing the Crossover Settings

Before performing the following procedures, refer to “About the Crossover” (Page 17).

1Press and hold MENU for at least 2 seconds.

2Select the Crossover (X-OVER) mode by sliding your finger on the GlideTouch bar to the left or right. Press the GlideTouch bar under the Crossover (X-OVER) mode.

2WAY System

3Press BAND to select the band to be adjusted.

LOW → MID → HIGH → LOW

(SUBW) (REAR) (FRONT) (SUBW)

4Select the desired cut-off frequency (Crossover Point) by sliding your finger on the GlideTouch bar to the left or right.

Adjustable frequency bands: 20Hz to 200Hz

(in 1/3 octave steps)

5Press SOURCE/POWER to adjust the slope.

Adjustable slope: 0 (FLAT), 1 (6dB/oct.), 2 (12dB/oct.) 3 (18dB/oct.) 4 (24dB/oct.)

6Adjust the output level by turning the Rotary encoder.

Adjustable output level: -12 to 0 dB.

7To adjust another band, repeat steps 3 to 6, then adjust all bands.

8When the setting has been completed, press FUNC. or the GlideTouch bar to activate the preset mode.

9Select any one of the preset numbers (1 through 6) by sliding your finger on the GlideTouch bar to the left or right. Press and hold the GlideTouch bar under the desire preset for at least 2 seconds to store the adjusted contents.

10After setting, press and hold MENU for at least 2 seconds to return to normal mode.

•If MENU is pressed while adjusting or setting the itmes in the MENU mode, the unit will return to the previous selection secreen.

•By pressing the GlideTouch bar under RETURN in the MENU mode, the unit will return to the normal mode.

•If no peration is performed in 60 seconds, the unit will return to the normal mode.

3 WAY System

3Press BAND to select the band to be adjusted.

LOW → MID-L → MID-H → HIGH → LOW

4Select the desired cut-off frequency (Crossover Point) by sliding your finger on the GlideTouch bar to the left or right.

Adjustable frequency bands:

LOW: 20Hz to 200Hz (in 1/3 octave steps)

MID-L: 20Hz to 200Hz (in 1/3 octave steps)

MID-H: 20Hz to 20kHz (in 1/3 octave steps)

HIGH: 1kHz to 20 kHz (in 1/3 octave steps)

5Press SOURCE/POWER to adjust the slope.

Adjustable slope: 0 (FLAT)*1, 1 (6dB/oct.), 2 (12dB/oct.) 3 (18dB/oct.), 4 (24dB/oct.)

*FLAT can be set for the HIGH slope only when USER'S is selected in “Setting the Response Slope for the High Range Speaker (TW SETUP)” (page 29). Depending on the response characteristics of the speaker, care should be taken when setting the response slope to FLAT, as speaker damage may result. With the CDA-9855, a message is displayed when the response slope for the high range speaker is set to FLAT.

6Adjust the output level by turning the Rotary encoder.

Adjustable output level: -12 to 0 dB.

7To adjust another band, repeat steps 3 to 6, then adjust all bands.

8When the setting has been completed, press FUNC. or the GlideTouch bar to activate the preset mode.

9Select any one of the preset numbers (1 through 6) by sliding your finger on the GlideTouch bar to the left or right. Press and hold the GlideTouch bar under the desire preset for at least 2 seconds to store the adjusted contents.

10After setting, press and hold MENU for at least 2 seconds to return to normal mode.

•If MENU is pressed while adjusting or setting the itmes in the MENU mode, the unit will return to the previous selection secreen.

•By pressing the GlideTouch bar under RETURN in the MENU mode, the unit will return to the normal mode.

•If no peration is performed in 60 seconds, the unit will return to the normal mode.

•About the 2way/3way system

You can switch to 2way/3way system mode with the 2way/3way switch on the bottom side of the unit (pages 45 to 47).

	When setting to “3 WAY”:
F/R Sub-W	The unit can be operated in a 3 way system.
3WAY	When setting to “F/R/Sub-W”:
	The unit can be operated in a 2 way system.

18-EN