Altinex MT107-103 manual 2. C, CnS, Multitasker

MULTITASKER

2.[C]

This command displays the active matrix configuration, input-to-output connections, and output on/off status.

Command Format: [Cn]

Cn = Card ID (n = slot # from 1 to max slots) Example:

There is an MT107-103in slot 8. Send [C8] and the card will return feedback in the following format:

Matrix mode:non-blocking Matrix number:1

Matrix size:64X64 Input offset:0 Output offset:0 Channel width:1 Channel space:0

OUT
1-8	:	1	1	1	1	1x	1x	1x	1x
9-16 :		9x	10x	11x	12x	13x	14x	15x	16x
17-24 : 17x 18x				19x 20x 21x 22x				23x 24x
25-32 : 25x 26x				27x 28x 29x 30x				31x 32x
33-40 : 33x 34x				35x 36x 37x 38x				39x 40x
41-48 : 41x 42x				43x 44x 45x 46x				47x 48x
49-56	: 49x		50x	51x	52x	53x	54x	55x	56x
57-64	:	57x	58x	59x	60x	61x	62x	63x	64x

Description of Feedback:

The first line of the status shows the matrix in non-blocking mode (see [MODE] command for details). The next line lists the matrix number followed by 5 lines that describe the properties of the matrix. The second half of the status, the remaining 8 lines, shows the input-to-output connections and the output on/off status.

In the above example, Matrix 1 is the active matrix and is configured as a 64X64 matrix with no input or output offset. The channel width is 1, and the channel spacing is 0, so each of the 64 inputs and outputs are switched individually.

The last 8 lines of the status are the connection settings, and each output on/off status. The top line shows the inputs that are connected to Outputs 1-8 and the next line shows the inputs that are connected to Outputs 9-16, and so on. The lowercase “x” next to the input number indicates that its output is turned off. In this case, Input 1 is connected to Outputs 1-8, Output 9 is connected to Input 9, Output 10 to Input 10, and so on. Outputs 5-64 are turned off.

3.[CnS]

This command saves the input-to-output connections and on/off settings. This configuration will be restored after the system is reset or powered off, then back on.

Command Format: [CnS]

Cn = Card ID (n = # from 1 to max slots) S = save configuration

Example:

Save the setup from the example in the previous command by sending [C8S]. The feedback would be as follows:

VIS:OFF

Matrix mode:non-blocking Matrix number:1

Matrix size:64X64 Input offset:0 Output offset:0 Channel width:1 Channel space:0

OUT
1-8	:	1	1	1	1	1x	1x	1x	1x
9-16 :		9x	10x	11x	12x	13x	14x	15x	16x
17-24 : 17x 18x				19x 20x 21x 22x				23x 24x
25-32 : 25x 26x				27x 28x 29x 30x				31x 32x
33-40 : 33x 34x				35x 36x 37x 38x				39x 40x
41-48 : 41x 42x				43x 44x 45x 46x				47x 48x
49-56	: 49x		50x	51x	52x	53x	54x	55x	56x
57-64	:	57x	58x	59x	60x	61x	62x	63x	64x

[SAVED]

400-0367-005 9