MULTITASKER
Input Cards |
| |||
4 | 3 | 2 |
| 1 |
|
|
|
|
|
1d | 1c | 1b |
| 1a |
|
|
|
|
|
2d | 2c | 2b |
| 2a |
|
|
|
|
|
3d | 3c | 3b |
| 3a |
|
|
|
|
|
4d | 4c | 4b |
| 4a |
|
|
|
|
|
5d | 5c | 5b |
| 5a |
|
|
|
|
|
6d | 6c | 6b |
| 6a |
|
|
|
|
|
7d | 7c | 7b |
| 7a |
|
|
|
|
|
8d | 8c | 8b |
| 8a |
|
|
|
|
|
Output Cards
1 | 2 | 3 | 4 |
|
|
|
|
1a | 1b | 1c | 1d |
|
|
|
|
2a | 2b | 2c | 2d |
|
|
|
|
3a | 3b | 3c | 3d |
|
|
|
|
4a | 4b | 4c | 4d |
|
|
|
|
5a | 5b | 5c | 5d |
|
|
|
|
6a | 6b | 6c | 6d |
|
|
|
|
7a | 7b | 7c | 7d |
|
|
|
|
8a | 8b | 8c | 8d |
|
|
|
|
18.[MjCn]
This command selects the matrix to be active.
Command Format: [MjCn]
j = Matrix ID (j = # from 1 to 9)
Cn = Card ID (n = slot # from 1 to max slots)
Example:
There is a Matrix Engine in slot 8. Send the command [M1C8] to recall the Matrix 1 configuration of C8.
RECALL MATRIX ON POWER-UP
In order to make Matrix 1’s configuration the default when power is turned on, send the
Example 2: [MAT1;16;16;00;00;02;00;C8S]
Inputs = 16
Outputs = 16
Input Offset = 00
Output Offset = 00
Width = 02
Spacing = 00
In this configuration, if Input 1 is connected to Output 16, the entire channel, 1a and 1b, will be switched to outputs 16a and 16b respectively.
[M1C8S]. The feedback will be similar to:
[SAVED]
19.[MODE]
This command sets the matrix switch mode to blocking or
Command Format: [MODEmCn]
m = 1 = ON, 0 = OFF
Cn = Card ID (n = slot # from 1 to max slots)
Input Cards
4 | 3 | 2 | 1 |
13a | 9a | 5a | 1a |
|
|
|
|
13b | 9b | 5b | 1b |
|
|
|
|
14a | 10a | 6a | 2a |
|
|
|
|
14b | 10b | 6b | 2b |
|
|
|
|
15a | 11a | 7a | 3a |
|
|
|
|
15b | 11b | 7b | 3b |
|
|
|
|
16a | 12a | 8a | 4a |
|
|
|
|
16b | 12b | 8b | 4b |
|
|
|
|
Output Cards
1 | 2 | 3 | 4 |
1a | 5a | 9a | 13a |
|
|
|
|
1b | 5b | 9b | 13b |
|
|
|
|
2a | 6a | 10a | 14a |
|
|
|
|
2b | 6b | 10b | 14b |
|
|
|
|
3a | 7a | 11a | 15a |
|
|
|
|
3b | 7b | 11b | 15b |
|
|
|
|
4a | 8a | 12a | 16a |
|
|
|
|
4b | 8b | 12b | 16b |
|
|
|
|
Example:
Send the command [MODE0C8] to turn off blocking for the engine in slot 8. Next, send the command [I1O*C8] to connect Input 1 to all outputs. In
Example: BLOCKING ON
Send the command [I1O*C8] to connect Input 1 to all outputs. With blocking on, Input 1 will be connected to all outputs, but only output 1 will be enabled. The remaining outputs will need to be enabled using the [ON] command.
Connecting a single output results in the output being switched and enabled. For example, sending [I22O22C8] with blocking on results in Input 22 being connected to Output 22, with Output 22 being enabled.
16 |
