To Replace Lint Drawer Switch | American Dryer Corp ML-170, ML-145

L.LINT DRAWER ASSEMBLY To Replace Lint Screen

1.Pull out lint drawer.

2.Remove lint screen from lint drawer.

3.Drop new lint screen in place.

4.Slide lint drawer back into dryer.

To Replace Lint Drawer Switch

1.Disconnect electrical power to the dryer.

2.Remove lint drawer and lint door.

3.Disconnect both 4-pin connectors at the rear of the lint switch cover.

4.Remove the pal nut holding the lint switch cover on.

5.Remove lint switch cover and disconnect the two (2) terminals of the switch.

6.Remove switch by pressing tabs together and push switch out.

7.Install new switch by reversing procedure.

34

Image 38

American Dryer Corp ML-170, ML-145 service manual Lint Drawer Assembly To Replace Lint Screen, To Replace Lint Drawer Switch

Contents

ML-145 / ML-170 American Dryer Corporation Retain This Manual In a Safe Place For Future Reference For Your Safety Page Table of Content Section Technical Information Safety Precautions Important Information Standards Routine Maintenance Cleaning Adjustments Lubrication Electrical and GAS Requirements Installation RequirementsENCLOSURE, AIR SUPPLY, and Exhaust Requirements Operational Service Check Procedure Gas 10.5 inches water column 26.1 mb Control Panel NON-MICROPROCESSOR Description of PartsControl Panel Microprocessor Control BOX Gas Models only GAS Burner AssemblyHSI HOT Surface Ignition Module Drive Motor Tumbler Basket Bearing and Pulley Arrangement Idler AssemblyBlower Motor and Impellor GAS and Steam Tumbler Basket Main Door SwitchSail Switch Gas Models only Lint Drawer Automatic Reset ThermostatHI-LIMIT Gas Models only Steam Damper System Lint Drawer SwitchTemperature Sensor Bracket NON-COMPUTER Compressed AIR Requirements Computer Controls ServicingIntroduction To Replace Computer To Replace Keyboard Touchpad Label Assembly To Replace Microprocessor Temperature Sensor Probe To Replace Gas Valve Refer to above burner illustration To Remove Flame Probe AssemblyIgnition Controls To Test and Adjust Gas Water Column Pressure To Replace Main Burner Orifices To Convert from Natural Gas to L.P. Gas To Replace Burner Tubes To Replace Burner Hi-Limit Thermostat Gas Models Only To Replace HSI Hot Surface Ignition ModuleThermostats Sail Switch Assembly Gas Models only To Replace Sail Switch To Adjust Sail Switch To Replace Main Door Assembly To Install New Main Door Glass To Replace Front Panel To Replace Tumbler Basket Pulley To Replace Main Door Hinge BlocksPulleys To Replace Small Idler Pulley To Replace Large Idler Pulley To Replace Motor Pulley Tumbler Basket AssemblyTumbler Basket Alignment Vertical Up and Down Adjustment Tumbler Basket Alignment Lateral Side to Side Adjustment To Replace Tumbler Basket or Tumbler Basket Support Important Never strike the shaft directly with a hammer To Replace Front Tumbler Basket Support Pillow Block Bearing To Replace Front Idler Shaft Pillow Block Bearing Belts Refer to illustrations in section F Pulleys Belt Tension Adjustment Tumbler Basket to IdlerTo Replace Rear Idler Shaft Pillow Block Bearing Motors Belt Tension Adjustment Motor to IdlerTo Replace V-Belts To Replace Drive Motor Impellor Lint Drawer Assembly To Replace Lint Screen To Replace Lint Drawer Switch Troubleshooting Computer will not accept keyboard touchpad entries Display is reading Rotation Sensor Fail Display is reading no Airflow Display is reading Burner Safety Fail Display is reading Sail Switch FailDisplay is reading Drum Safety Fail Display is reading No Heat Display is reading Main Door Display is reading Burner Control FailureDisplay is reading Burner Flame Failure Display is reading Lint Door Thermal overload for drive motor is tripping Display is reading HotDryer operates but is taking too long to dry Overload for impellor fan motor is tripping There is excessive vibration coming from the tumbler basket Electrical Troubleshooting Phase 6 OPL System Diagnostics Diagnostic L.E.D. light emitting diode Display Failure CodesPage E.D. light emitting diode Display Indicators E.D. Display Indicator Number E.D. Display Indicator Number HT1 Heat Output L.E.D. Indicator FAN Blower Output L.E.D. light emitting diode IndicatorAIR AIR JET Output L.E.D. Indicator Optional Main Main Door Input L.E.D. Indicator Fuse Main Fuse Input L.E.D. IndicatorLint Lint Door Input L.E.D. Indicator Drum Tumbler Basket HI-LIMIT Input L.E.D. Indicator Flame bURNER Control Fail Input L.E.D. Indicator Power Supply Input L.E.D. Indicator D. DISPLAY/CODES E.D. Display Operating Status Phase 6 OPL Microprocessor L.E.D. Displays E.D. Codes 1. Display Codes ALL REV GAS only Ignition Attempt Failure GAS Models only Power 24 VAC is not Evident AT GAS ValveGAS/ELECTRIC only BURNER/OVEN Open HI-LIMIT Circuit Computer Logic and Wiring Diagram No Display Condition Blower motor does not operate, drive motor runs No Heat Drive and Blower Motors Run Gas Models No Heat Drive and Blower Motors Run Steam Models Door Condition Technical Information Motor Plate High and LOW Voltage Data Label Information on the Data Label Using a Manometer How to Use a Manometer ML-170 Tool List ADC 450429 1- 02/18/00-25