Ampro Corporation 5001451A Floppy Disk Interface

Little Board P6d Module

2-25

SELIN* Printer select input This bit is inverted and output to the pin. It selects a printer.

IRQE Interrupt request

enable When set to 1, interrupts are enabled. An interrupt is generated by

the positive-going -ACK input.

PCD Par allel control

direction When set to 1, port is in input mode. In printer mode, the printer is

always in output mode regardless of the state of this bit.

PD0-PD7 Parallel Data Bits

Floppy Disk Interface

The on-board floppy disk controller and ROM BIOS support one or two floppy disk drives in any of

the standard DOS formats shown in Table 2-24.

Table 2-24. Supported Floppy Formats

Capacity Drive Size Tracks Data Rate

360K 5-1/4 inch 40 250KHz

1.2M 5-1/4 inch 80 500KHz

720K 3-1/2 inch 80 250KHz

1.44M 3-1/2 inch 80 500KHz

Floppy Drive Considerations

Nearly any type of soft-sectored, single or double-sided, 40 or 80 track, 5-1/4 in ch or 3- 1/2 inch

floppy disk drive is usable with this interface. Using higher quality drive s improv es syste m

reliability. Here are some considerations about the selection, configuration, and conn ection o f

floppy drives to the Little Board P6d module.

Drive Interface—The drives must be compatible with the board’s floppy disk signal in terface , as

described below. Ampro recommends any standard PC-or AT-compatible 5-1/4 inch or 3-1/2 inch

floppy drive.

Drive Quality—Use high quality, DC servo, direct drive motor floppy disk driv es.

Drive Select Jumpering—Both drives must be jumpered to the second drive select.

Floppy Cable—For systems with two drives, use a floppy cable with conductors 10-16 twisted

between the two drives. This is standard practice for PC-compatible systems.

Head Load Jumpering—When using drives with a Head Load option, jumper the drive for head load

with motor on rather than head load with drive select. This is the def ault fo r PC-co mpatible drive s.

Drive Mounting—If you mount a floppy drive very close to the Little Board or another source of

EMI, you may need to place a thin metal shield between the d isk drive and the dev ice to redu ce th e

possibility of electromagnetic interference.

Floppy Interface Configuration

The floppy interface is configured using Setup to set the number and type of floppy drives connected

to the system. Refer to the Setup section starting on page 2–48 for d etails.

Contents

Main Revision Reason for Change Date Table of Contents Preface Introduction Product Reference Page Technical Specifications Standards Contact Information Cables Index Page Preface Introduction Technical Support Page Chapter 1 Introduction General Description Product Feature Summary CPU/Motherboard Enhanced Embedded-PC BIOS Modular PC/104-Plus Expansion Bus CompactFlash Disk Serial Ports Parallel Port Floppy Interface PCI-Bus EIDE Interfaces PCI Audio Interface Flat Panel/CRT Display Controller 100 MBps Ethernet LAN Interface Enhanced Reliability Software Designing Little Board Systems On-board MiniModule Expansion Little Board Development Platform And QuickStart Kit Figure 1-1. I/O Development Board Connector Descriptions J1 Utility J2 Power J3 Misc. J4 Keyboard Switch Descriptions (S1 S5) Figure 1-2. System Block Diagram Page Chapter 2 Product Reference Overview Mounting Dimensions 2-2 Figure 2-1. Little Board P6d Module with Mounting Dimensions Connector Summary Page 2-5 Figure 2-2. Little Board P6d Connector and Jumper Locations Jumper Summary DC Power Power Requirements Other Voltages Switching Power Supplies Powerfail NMI Cooling Requirements Thermal Sensor Fan Connector Figure 2-3. CPU Fan Connection (J21) System Memory ROM BIOS Shadowing BIOS Recovery Interrupt and DMA Channel Usage Page Battery-Backed Clock Serial Ports I/O Addresses and Interrupt Assignments ROM-BIOS Installation of the Serial Ports Serial Port Connectors (J8, J11) Page Serial TTL Option Ampro Custom Serial Features Serial Console Features Using a Standard PC Keyboard Using Arrow Keys During Setup COM Port Table Universal Serial Bus (USB) Ports Infrared (IrDA) Interface Requirements for an IrDA Interface IrDA Connector (Part of Utility J19) Multi-Mode Parallel Port I/O Addresses and Interrupts ROM-BIOS Installation of Parallel Ports Page IEEE-1284-compliant Cables Latch-Up Protection Parallel Port Registers Standard and Bidirectional Operation Using the Parallel Port in Bidirectional Mode Using the Control Lines for Additional I/O Enabling the Parallel Port Interrupt Page Floppy Disk Interface Floppy Drive Considerations Floppy Interface Configuration Floppy Interface Connector (J14) EIDE Hard Disk Interface Pin # Signal Name Function Pin # Signal Name Function IDE Interface Configuration CompactFlash Solid-State Disk Enabling the Drive Master/Slave Setting Solid-State Disk Preparation Audio Interface Audio Amplifier Figure 2-4. Little Board P6d Audio Interface Adapter Audio Interface Connector Page 2-31 Figure 2-5. Audio Interface Adapter Schematic HEAD PHONE MIC IN PHONE IN SPEAKER OUT Flat Panel/CRT Video Controller Connecting a Flat Panel (J15) Power Sequencing Advanced Power Management BIOS Support of Standard Flat Panels Connecting a CRT (J17) ZV Port Interface (J16) Disabling the Video Controller Ethernet Network Interface Hardware Description Ethernet RJ45 Interface Connector (J13) Ethernet Interface Software Manufacturer's Ethernet ID Network Operating Systems Network OS Drivers Ethernet Setup Watchdog Timer Utility Connectors (J19) Pin # Signal Name Function Pin # Signal Name Function LED Connection Speaker Connections Push-button Reset Connection Keyboard Connection PS/2 Mouse Connection PC/104-Plus Expansion Bus On-board MiniModule Expansion Details Figure 2-6. Stacking PC/104 Modules on the Little Board P6d Module Using Standard PC and AT Bus Cards Expansion Bus Connector Pinouts Page Page 2-47 Table 2-45. PC/104-Plus Expansion Bus Connector, J3 (A1-D30) PinABCD Notes: Setup Setup Help Page Setup 1 Main Menu Figure 2-7. Setup 1 Main Menu Setup 2 Standard CMOS Setup Figure 2-8. Setup 2 Standard CMOS Setup EIDE Hard Disk Drives Drive Selection Floppy Drives Drive Parameter Setup Video Error Halt Setup 3 BIOS Features Setup Figure 2-9. Setup 3 BIOS Features Setup Serial Console Operation during SETUP. Setup 4 Chipset Features Setup Figure 2-10. Setup 4 Chipset Features Setup Setup 5 Power Management Setup Figure 2-11. Setup 5 Power Management Setup Page Setup 6 PCI Configuration Setup Figure 2-12. Setup 6 PCI Configuration Setup Setup 7 Integrated Peripherals Setup Figure 2-13. Setup 7 Integrated Peripherals Setup Panel # Panel Class Other Setup Screens Load Setup Defaults Screen Figure 2-15. IDE HDD Auto Detection Screen Figure 2-14. Load Setup Defaults Screen IDE HDD Auto Detection Screen Save & Exit Setup Screen Figure 2-16. Save & Exit Setup Screen Exit Without Saving Screen Figure 2-17. Exit Without Saving Screen Chapter 3 Technical Specifications Little Board P6d Technical Specifications CPU/Motherboard Embedded-PC System Enhancements On-board Peripherals Support Software Mechanical and Environmental Specifications Flat Panel Displays BIOS Modes 3-5 Table 3-1. Supported CRT Video ModesStandard VGA 3-6 Table 3-2. Supported CRT Video ModesLow Resolution Note: All modes in this table are Graphical and Linear, except where noted. 3-7 Table 3-3. Supported CRT Video ModesExtended Modes 3-8 Hardware IRQ Map Page Appendix A Standards Contact Information EPP and ECP Operation Page Page Page Index A B C D I J K L M T U V W