Ampro Corporation 5001451A Setup 4 Chipset Features Setup

Little Board P6d Module

2-55

! F keys – F keys are entered with two keystrokes. The first entry is "F" follo wed by the numbe r.

So that "F" followed by "1" is the same as using the "F1" key. F10 is simulated by ente ring F0,

"F" and "0".

Note

This unique operation only occurs during SETUP.

Setup 4 — Chipset Features Setup

Setup 4 — Chipset Features Setup controls internal chipset features. The OEM or end user should

never change most of these items, as they specify internal parameters that have been chosen to

support the existing motherboard design. Change these parameters only if directed to by Ampro

Technical Support. Figure 2-10 shows what can be configured on Setup 4. Th e item s that can be

changed by the OEM are listed below.

Chipset Features Setup

Ampro Computers, Inc.

CPU Warning Temperature:100ºC/212ºF

Current CPU Temperature:68ºC/154ºF

Auto Configuration :Enabled

EDO DRAM Speed Selection :60ns

EDO CASx# MA Wait State :2

EDO RASx# Wait State :2

SDRAM RAS-to-CAS Delay :3

SDRAM RAS Precharge Time :3

SDRAM CAS Latency Time :3

SDRAM Prechard Control :Disabled

DRAM Data Integrity Mode :Non-ECC

System BIOS Cacheable :Disabled

Video BIOS Cacheable :Disabled

Video RAM Cacheable :Disabled

8 Bit I/O Recovery Time :1

16 Bit I/O Recovery Time :1

Memory Hole At 15M-16M :Disabled

Passive Release :Enabled

Delayed Transaction :Disabled

AGP Aperture Size :64

ESC:Quit ↑↓→← : Select Item

F1 :Help PU/PD/+/- : Modify

F5 :Old Values (Shift)F2:Color

F6 :Load BIOS Defaults

F7 :Load Setup Defaults

Figure 2-10. Setup 4 — Chipset Features Setup

This Chipset Features Setup screen allows you to configure the follo wing paramete rs:

! AUTO CONFIGURATION — This controls the configuration of DRAM and SDRAM timing.

! MEMORY HOLE AT 15M-16M — Local Memory option creates a 1 Meg memory hole below 16

Meg (special video hardware) and is only used by external video or a video board located in an

ISA bus slot.

Contents

Main Revision Reason for Change Date Table of Contents Preface Introduction Product Reference Page Technical Specifications Standards Contact Information Cables Index Page Preface Introduction Technical Support Page Chapter 1 Introduction General Description Product Feature Summary CPU/Motherboard Enhanced Embedded-PC BIOS Modular PC/104-Plus Expansion Bus CompactFlash Disk Serial Ports Parallel Port Floppy Interface PCI-Bus EIDE Interfaces PCI Audio Interface Flat Panel/CRT Display Controller 100 MBps Ethernet LAN Interface Enhanced Reliability Software Designing Little Board Systems On-board MiniModule Expansion Little Board Development Platform And QuickStart Kit Figure 1-1. I/O Development Board Connector Descriptions J1 Utility J2 Power J3 Misc. J4 Keyboard Switch Descriptions (S1 S5) Figure 1-2. System Block Diagram Page Chapter 2 Product Reference Overview Mounting Dimensions 2-2 Figure 2-1. Little Board P6d Module with Mounting Dimensions Connector Summary Page 2-5 Figure 2-2. Little Board P6d Connector and Jumper Locations Jumper Summary DC Power Power Requirements Other Voltages Switching Power Supplies Powerfail NMI Cooling Requirements Thermal Sensor Fan Connector Figure 2-3. CPU Fan Connection (J21) System Memory ROM BIOS Shadowing BIOS Recovery Interrupt and DMA Channel Usage Page Battery-Backed Clock Serial Ports I/O Addresses and Interrupt Assignments ROM-BIOS Installation of the Serial Ports Serial Port Connectors (J8, J11) Page Serial TTL Option Ampro Custom Serial Features Serial Console Features Using a Standard PC Keyboard Using Arrow Keys During Setup COM Port Table Universal Serial Bus (USB) Ports Infrared (IrDA) Interface Requirements for an IrDA Interface IrDA Connector (Part of Utility J19) Multi-Mode Parallel Port I/O Addresses and Interrupts ROM-BIOS Installation of Parallel Ports Page IEEE-1284-compliant Cables Latch-Up Protection Parallel Port Registers Standard and Bidirectional Operation Using the Parallel Port in Bidirectional Mode Using the Control Lines for Additional I/O Enabling the Parallel Port Interrupt Page Floppy Disk Interface Floppy Drive Considerations Floppy Interface Configuration Floppy Interface Connector (J14) EIDE Hard Disk Interface Pin # Signal Name Function Pin # Signal Name Function IDE Interface Configuration CompactFlash Solid-State Disk Enabling the Drive Master/Slave Setting Solid-State Disk Preparation Audio Interface Audio Amplifier Figure 2-4. Little Board P6d Audio Interface Adapter Audio Interface Connector Page 2-31 Figure 2-5. Audio Interface Adapter Schematic HEAD PHONE MIC IN PHONE IN SPEAKER OUT Flat Panel/CRT Video Controller Connecting a Flat Panel (J15) Power Sequencing Advanced Power Management BIOS Support of Standard Flat Panels Connecting a CRT (J17) ZV Port Interface (J16) Disabling the Video Controller Ethernet Network Interface Hardware Description Ethernet RJ45 Interface Connector (J13) Ethernet Interface Software Manufacturer's Ethernet ID Network Operating Systems Network OS Drivers Ethernet Setup Watchdog Timer Utility Connectors (J19) Pin # Signal Name Function Pin # Signal Name Function LED Connection Speaker Connections Push-button Reset Connection Keyboard Connection PS/2 Mouse Connection PC/104-Plus Expansion Bus On-board MiniModule Expansion Details Figure 2-6. Stacking PC/104 Modules on the Little Board P6d Module Using Standard PC and AT Bus Cards Expansion Bus Connector Pinouts Page Page 2-47 Table 2-45. PC/104-Plus Expansion Bus Connector, J3 (A1-D30) PinABCD Notes: Setup Setup Help Page Setup 1 Main Menu Figure 2-7. Setup 1 Main Menu Setup 2 Standard CMOS Setup Figure 2-8. Setup 2 Standard CMOS Setup EIDE Hard Disk Drives Drive Selection Floppy Drives Drive Parameter Setup Video Error Halt Setup 3 BIOS Features Setup Figure 2-9. Setup 3 BIOS Features Setup Serial Console Operation during SETUP. Setup 4 Chipset Features Setup Figure 2-10. Setup 4 Chipset Features Setup Setup 5 Power Management Setup Figure 2-11. Setup 5 Power Management Setup Page Setup 6 PCI Configuration Setup Figure 2-12. Setup 6 PCI Configuration Setup Setup 7 Integrated Peripherals Setup Figure 2-13. Setup 7 Integrated Peripherals Setup Panel # Panel Class Other Setup Screens Load Setup Defaults Screen Figure 2-15. IDE HDD Auto Detection Screen Figure 2-14. Load Setup Defaults Screen IDE HDD Auto Detection Screen Save & Exit Setup Screen Figure 2-16. Save & Exit Setup Screen Exit Without Saving Screen Figure 2-17. Exit Without Saving Screen Chapter 3 Technical Specifications Little Board P6d Technical Specifications CPU/Motherboard Embedded-PC System Enhancements On-board Peripherals Support Software Mechanical and Environmental Specifications Flat Panel Displays BIOS Modes 3-5 Table 3-1. Supported CRT Video ModesStandard VGA 3-6 Table 3-2. Supported CRT Video ModesLow Resolution Note: All modes in this table are Graphical and Linear, except where noted. 3-7 Table 3-3. Supported CRT Video ModesExtended Modes 3-8 Hardware IRQ Map Page Appendix A Standards Contact Information EPP and ECP Operation Page Page Page Index A B C D I J K L M T U V W