Ampro Corporation 5001451A Setup 3 BIOS Features Setup

Little Board P6d Module

2-53

Video

Specify the initial video mode. Select Mono, CGA40, CGA80, or EGA/VGA. If your vide o display

card is VGA, super VGA, or any other high resolution standard, specify EGA/VGA no matter how it

is configured to come up.

Error Halt

Select which kinds of errors will halt the Power-On Self Test (POST). If you p lan to use the mod ule

without a keyboard, be sure to set this option to not halt on ke yboar d err or.

DRAM Memory

The ROM BIOS automatically detects the amount of memory during POST and stores the result

when you save the configuration values when exiting Setup . This Setup page display s the amou nt

of memory found in the system.

Setup 3 — BIOS Features Setup

Use Setup 3 to set a variety of BIOS feature options. Figure 2-9 shows what can be configured on

Setup 3, and the sections that follow describe each parameter.

BIOS FEATURES Setup

Ampro Computers, Inc.

Video BIOS Shadow : Enabled

Serial Console : Disabled

Serial Boot Loader : Disabled

Virus Warning : Disabled

CPU Internal Cache : Enabled

External Cache : Disabled

Quick Power On Self Test : Disabled

Boot Sequence : A,C,SCSI

Swap Floppy Drive : Disabled

Boot Up Floppy Seek : Enabled

Boot Up Numlock Status : Off

Gate A20 Option : Fast

Typematic Rate Setting : Disabled

Typematic Rate (chars/Sec) : 6

Typematic Delay(Msec) : 250

PS/2 mouse function : Disabled

PCI/VGA Palette Snoop : Disabled

OS Select for DRAM >64MB : Non-OS2

Report No FDD For WIN 95 : Yes

Watchdog Timer : Disabled

ESC:Quit ↑↓→←: Select

Item

F1 :Help PU/PD/+/- : Modify

F5 :Old Values (Shift)F2:Color

F6 :Load BIOS Defaults

F7 :Load Setup Defaults

Figure 2-9. Setup 3 — BIOS Features Setup

This Setup screen allows you to configure the following parameters:

! VIRUS WARNING – default is disabled. Virus Warning monitors for writes to the hard disk

boot sector. It will display the following warning message, beep the spe aker and w ait for use r

confirmation.

Contents

Main Revision Reason for Change Date Table of Contents Preface Introduction Product Reference Page Technical Specifications Standards Contact Information Cables Index Page Preface Introduction Technical Support Page Chapter 1 Introduction General Description Product Feature Summary CPU/Motherboard Enhanced Embedded-PC BIOS Modular PC/104-Plus Expansion Bus CompactFlash Disk Serial Ports Parallel Port Floppy Interface PCI-Bus EIDE Interfaces PCI Audio Interface Flat Panel/CRT Display Controller 100 MBps Ethernet LAN Interface Enhanced Reliability Software Designing Little Board Systems On-board MiniModule Expansion Little Board Development Platform And QuickStart Kit Figure 1-1. I/O Development Board Connector Descriptions J1 Utility J2 Power J3 Misc. J4 Keyboard Switch Descriptions (S1 S5) Figure 1-2. System Block Diagram Page Chapter 2 Product Reference Overview Mounting Dimensions 2-2 Figure 2-1. Little Board P6d Module with Mounting Dimensions Connector Summary Page 2-5 Figure 2-2. Little Board P6d Connector and Jumper Locations Jumper Summary DC Power Power Requirements Other Voltages Switching Power Supplies Powerfail NMI Cooling Requirements Thermal Sensor Fan Connector Figure 2-3. CPU Fan Connection (J21) System Memory ROM BIOS Shadowing BIOS Recovery Interrupt and DMA Channel Usage Page Battery-Backed Clock Serial Ports I/O Addresses and Interrupt Assignments ROM-BIOS Installation of the Serial Ports Serial Port Connectors (J8, J11) Page Serial TTL Option Ampro Custom Serial Features Serial Console Features Using a Standard PC Keyboard Using Arrow Keys During Setup COM Port Table Universal Serial Bus (USB) Ports Infrared (IrDA) Interface Requirements for an IrDA Interface IrDA Connector (Part of Utility J19) Multi-Mode Parallel Port I/O Addresses and Interrupts ROM-BIOS Installation of Parallel Ports Page IEEE-1284-compliant Cables Latch-Up Protection Parallel Port Registers Standard and Bidirectional Operation Using the Parallel Port in Bidirectional Mode Using the Control Lines for Additional I/O Enabling the Parallel Port Interrupt Page Floppy Disk Interface Floppy Drive Considerations Floppy Interface Configuration Floppy Interface Connector (J14) EIDE Hard Disk Interface Pin # Signal Name Function Pin # Signal Name Function IDE Interface Configuration CompactFlash Solid-State Disk Enabling the Drive Master/Slave Setting Solid-State Disk Preparation Audio Interface Audio Amplifier Figure 2-4. Little Board P6d Audio Interface Adapter Audio Interface Connector Page 2-31 Figure 2-5. Audio Interface Adapter Schematic HEAD PHONE MIC IN PHONE IN SPEAKER OUT Flat Panel/CRT Video Controller Connecting a Flat Panel (J15) Power Sequencing Advanced Power Management BIOS Support of Standard Flat Panels Connecting a CRT (J17) ZV Port Interface (J16) Disabling the Video Controller Ethernet Network Interface Hardware Description Ethernet RJ45 Interface Connector (J13) Ethernet Interface Software Manufacturer's Ethernet ID Network Operating Systems Network OS Drivers Ethernet Setup Watchdog Timer Utility Connectors (J19) Pin # Signal Name Function Pin # Signal Name Function LED Connection Speaker Connections Push-button Reset Connection Keyboard Connection PS/2 Mouse Connection PC/104-Plus Expansion Bus On-board MiniModule Expansion Details Figure 2-6. Stacking PC/104 Modules on the Little Board P6d Module Using Standard PC and AT Bus Cards Expansion Bus Connector Pinouts Page Page 2-47 Table 2-45. PC/104-Plus Expansion Bus Connector, J3 (A1-D30) PinABCD Notes: Setup Setup Help Page Setup 1 Main Menu Figure 2-7. Setup 1 Main Menu Setup 2 Standard CMOS Setup Figure 2-8. Setup 2 Standard CMOS Setup EIDE Hard Disk Drives Drive Selection Floppy Drives Drive Parameter Setup Video Error Halt Setup 3 BIOS Features Setup Figure 2-9. Setup 3 BIOS Features Setup Serial Console Operation during SETUP. Setup 4 Chipset Features Setup Figure 2-10. Setup 4 Chipset Features Setup Setup 5 Power Management Setup Figure 2-11. Setup 5 Power Management Setup Page Setup 6 PCI Configuration Setup Figure 2-12. Setup 6 PCI Configuration Setup Setup 7 Integrated Peripherals Setup Figure 2-13. Setup 7 Integrated Peripherals Setup Panel # Panel Class Other Setup Screens Load Setup Defaults Screen Figure 2-15. IDE HDD Auto Detection Screen Figure 2-14. Load Setup Defaults Screen IDE HDD Auto Detection Screen Save & Exit Setup Screen Figure 2-16. Save & Exit Setup Screen Exit Without Saving Screen Figure 2-17. Exit Without Saving Screen Chapter 3 Technical Specifications Little Board P6d Technical Specifications CPU/Motherboard Embedded-PC System Enhancements On-board Peripherals Support Software Mechanical and Environmental Specifications Flat Panel Displays BIOS Modes 3-5 Table 3-1. Supported CRT Video ModesStandard VGA 3-6 Table 3-2. Supported CRT Video ModesLow Resolution Note: All modes in this table are Graphical and Linear, except where noted. 3-7 Table 3-3. Supported CRT Video ModesExtended Modes 3-8 Hardware IRQ Map Page Appendix A Standards Contact Information EPP and ECP Operation Page Page Page Index A B C D I J K L M T U V W