Ampro Corporation 5001451A Setup 2 Standard CMOS Setup

Little Board P6d Module

2-51

Setup 2 — Standard CMOS Setup

Use Setup 2 to set the date and time, configure your hard and floppy disks, and report system

memory. Figure 2-8 shows what can be configured on Setup 2, and the sectio ns that fo llow de scribe

each parameter.

STANDARD CMOS Setup

Ampro Computers, Inc.

Date (mm:dd:yyyy) : Wed, Feb 23, 1998

Time (hh:mm:ss) : 8 : 17 : 25

HARD DISK TYPE SIZE CYLS HEAD PRECOMP LANDZ SECTOR MODE

Primary Master : Auto 0 0 0 0 0 0 AUTO

Primary Slave : Auto 0 0 0 0 0 0 AUTO

Secondary Master : Auto 0 0 0 0 0 0 AUTO

Secondary Slave : Auto 0 0 0 0 0 0 AUTO

Drive A : 1.44M, 3.5 in.

Drive B : None

Video : EGA/VGA

Halt On : All Errors

Base Memory: 640K

Extended Memory: 31744K

Other Memory: 384K

────────────────────────

Total Memory: 32768K

ESC : Quit ↑↓→← : Select Item PU/PD/+/- : Modify

F1 : Help (Shift)F2 : Change Color

Figure 2-8. Setup 2 — Standard CMOS Setup

The Standard CMOS Setup screen allows you to configure the following parameters:

! DATE – Requires the numeric entry of mm:dd:yyyy. Calendar month is displayed and year

requires all 4 digits of century plus year.

! No parameters are displayed for auto-detect hard disk.

! The value displayed for Other Memory is required and utilized for system BIOS, video BIOS,

and other system extension ROM shadowing. It is not available for general OEM use.

! HARD DISK – When Auto TYPE is used the MODE should also be AUTO.

! When using any IDE hard drive, Auto is the best choice.

EIDE Hard Disk Drives

The module supports up to two hard disk drives connected to the IDE interface. Only hard disk

drives are directly supported in the system’s ROM BIOS. IDE CD-ROM drives and other IDE-

interfaced peripherals are configured by software or drivers supplied separately.

Physical drives can have one or more logical partitions. You can install up to eight logical dr ives

using drive partitions. To configure the system for the IDE hard drive s in you r syste m, set the

drive parameters with Setup, as outlined here:

Drive Types — the configuration memory contains a default list of parameters that specify the

physical format of each drive. Each type specifies the total number of cylinders, number of heads,

cylinder to begin precompensation, landing zone cylinder number, and the number of sectors per

Contents

Main Revision Reason for Change Date Table of Contents Preface Introduction Product Reference Page Technical Specifications Standards Contact Information Cables Index Page Preface Introduction Technical Support Page Chapter 1 Introduction General Description Product Feature Summary CPU/Motherboard Enhanced Embedded-PC BIOS Modular PC/104-Plus Expansion Bus CompactFlash Disk Serial Ports Parallel Port Floppy Interface PCI-Bus EIDE Interfaces PCI Audio Interface Flat Panel/CRT Display Controller 100 MBps Ethernet LAN Interface Enhanced Reliability Software Designing Little Board Systems On-board MiniModule Expansion Little Board Development Platform And QuickStart Kit Figure 1-1. I/O Development Board Connector Descriptions J1 Utility J2 Power J3 Misc. J4 Keyboard Switch Descriptions (S1 S5) Figure 1-2. System Block Diagram Page Chapter 2 Product Reference Overview Mounting Dimensions 2-2 Figure 2-1. Little Board P6d Module with Mounting Dimensions Connector Summary Page 2-5 Figure 2-2. Little Board P6d Connector and Jumper Locations Jumper Summary DC Power Power Requirements Other Voltages Switching Power Supplies Powerfail NMI Cooling Requirements Thermal Sensor Fan Connector Figure 2-3. CPU Fan Connection (J21) System Memory ROM BIOS Shadowing BIOS Recovery Interrupt and DMA Channel Usage Page Battery-Backed Clock Serial Ports I/O Addresses and Interrupt Assignments ROM-BIOS Installation of the Serial Ports Serial Port Connectors (J8, J11) Page Serial TTL Option Ampro Custom Serial Features Serial Console Features Using a Standard PC Keyboard Using Arrow Keys During Setup COM Port Table Universal Serial Bus (USB) Ports Infrared (IrDA) Interface Requirements for an IrDA Interface IrDA Connector (Part of Utility J19) Multi-Mode Parallel Port I/O Addresses and Interrupts ROM-BIOS Installation of Parallel Ports Page IEEE-1284-compliant Cables Latch-Up Protection Parallel Port Registers Standard and Bidirectional Operation Using the Parallel Port in Bidirectional Mode Using the Control Lines for Additional I/O Enabling the Parallel Port Interrupt Page Floppy Disk Interface Floppy Drive Considerations Floppy Interface Configuration Floppy Interface Connector (J14) EIDE Hard Disk Interface Pin # Signal Name Function Pin # Signal Name Function IDE Interface Configuration CompactFlash Solid-State Disk Enabling the Drive Master/Slave Setting Solid-State Disk Preparation Audio Interface Audio Amplifier Figure 2-4. Little Board P6d Audio Interface Adapter Audio Interface Connector Page 2-31 Figure 2-5. Audio Interface Adapter Schematic HEAD PHONE MIC IN PHONE IN SPEAKER OUT Flat Panel/CRT Video Controller Connecting a Flat Panel (J15) Power Sequencing Advanced Power Management BIOS Support of Standard Flat Panels Connecting a CRT (J17) ZV Port Interface (J16) Disabling the Video Controller Ethernet Network Interface Hardware Description Ethernet RJ45 Interface Connector (J13) Ethernet Interface Software Manufacturer's Ethernet ID Network Operating Systems Network OS Drivers Ethernet Setup Watchdog Timer Utility Connectors (J19) Pin # Signal Name Function Pin # Signal Name Function LED Connection Speaker Connections Push-button Reset Connection Keyboard Connection PS/2 Mouse Connection PC/104-Plus Expansion Bus On-board MiniModule Expansion Details Figure 2-6. Stacking PC/104 Modules on the Little Board P6d Module Using Standard PC and AT Bus Cards Expansion Bus Connector Pinouts Page Page 2-47 Table 2-45. PC/104-Plus Expansion Bus Connector, J3 (A1-D30) PinABCD Notes: Setup Setup Help Page Setup 1 Main Menu Figure 2-7. Setup 1 Main Menu Setup 2 Standard CMOS Setup Figure 2-8. Setup 2 Standard CMOS Setup EIDE Hard Disk Drives Drive Selection Floppy Drives Drive Parameter Setup Video Error Halt Setup 3 BIOS Features Setup Figure 2-9. Setup 3 BIOS Features Setup Serial Console Operation during SETUP. Setup 4 Chipset Features Setup Figure 2-10. Setup 4 Chipset Features Setup Setup 5 Power Management Setup Figure 2-11. Setup 5 Power Management Setup Page Setup 6 PCI Configuration Setup Figure 2-12. Setup 6 PCI Configuration Setup Setup 7 Integrated Peripherals Setup Figure 2-13. Setup 7 Integrated Peripherals Setup Panel # Panel Class Other Setup Screens Load Setup Defaults Screen Figure 2-15. IDE HDD Auto Detection Screen Figure 2-14. Load Setup Defaults Screen IDE HDD Auto Detection Screen Save & Exit Setup Screen Figure 2-16. Save & Exit Setup Screen Exit Without Saving Screen Figure 2-17. Exit Without Saving Screen Chapter 3 Technical Specifications Little Board P6d Technical Specifications CPU/Motherboard Embedded-PC System Enhancements On-board Peripherals Support Software Mechanical and Environmental Specifications Flat Panel Displays BIOS Modes 3-5 Table 3-1. Supported CRT Video ModesStandard VGA 3-6 Table 3-2. Supported CRT Video ModesLow Resolution Note: All modes in this table are Graphical and Linear, except where noted. 3-7 Table 3-3. Supported CRT Video ModesExtended Modes 3-8 Hardware IRQ Map Page Appendix A Standards Contact Information EPP and ECP Operation Page Page Page Index A B C D I J K L M T U V W