Manuals / Antec / Computer Equipment / Computer Accessories

Antec Included Fans, Standard fans on the DF-35 A -1 x 120 mm rear TwoCool LED fan, A B C

Models: DF-35

1 33

Download 33 pages 369 b

Page 29

Image 29

4.1

INCLUDED FANS

A

Standard fans on the DF-35:

A –1 x 120 mm rear TwoCool™ LED fan

B – 1 x 140 mm top TwoCool™ fan

C – 2 x Fleet-Release access door modules w/front variable-speed 120 mm white LED fans

Rear fan control panel

Page 29

Image 29

Antec Included Fans, Standard fans on the DF-35 A -1 x 120 mm rear TwoCool LED fan, B - 1 x 140 mm top TwoCool fan

Contents

THE ADVANCED GAMING FORCE D F - 3DARKFLEET U S E R M A N U A LDisclaimer DF-35 USER’S MANUALTABLE OF CONTENTS SECTION 1 INTRODUCTION Drive bays Power supply mounts5.25” drive bays 3.5” drive baysCASE SPECIFICATIONS BEFORE YOU BEGIN LOCATING AND POSITIONING YOUR COMPUTER SECTION 2 HARDWARE INSTALLATIONSETTING UP D - Front panel wiring E - I/O panel A - Power supply mounts B - 5.25” drive bay areaC - 3.5” drive bay area with Fleet-Swap SATA bays E D B C ABefore proceeding MOTHERBOARD INSTALLATIONMake sure you have the correct I/O panel. This mismatched I/O panel can cause difficulties down the road4. Install standoffs as needed and put the motherboard back in Lift your motherboard out to install the standoffsStep 5 Screwing in the motherboard after standoffs are installed 3. Now remove your motherboard by lifting it upThe DF-35 can accommodate a standard-size ATX power supply STANDARD ATX POWER SUPPLY INSTALLATIONNote The DF-35 comes with a CPU cutout on the motherboard tray, which PSU resting on the standard PSU mount3. Use the cable ties provided to hold them in place Use these screws to secure your power supply to the caseCABLE MANAGEMENT 1. Open the Fleet-ReleaseTM access door INTERNAL 3.5” DEVICE INSTALLATIONOpening the Fleet-Release access door by gently Installing a 3.5” internal deviceEXTERNAL 3.5” DEVICE INSTALLATION Make sure to install screws on the left side…4. Mount any other 3.5” HDD devices accordingly Remove this drive bay coverInsert your drive as shown USING FLEET-SWAPFleet-Swap default locations Moving or removing a Fleet-Swap bay A - Fleet-Swap SATA and power connectors B - Fleet-Swap bay screwsA B AB 3. Mount any other 3.5” HDD devices accordingly One example of AHCI configuration - your motherboard may varyLoading a Fleet-Swap drive Removing a Fleet-Swap drive 4. Close the Fleet-ReleaseTM Access Door3. Grasp the top and bottom of your HDD. Now pull the HDD free Using the top 2.5” hot-swap drive bay USING THE TOP 2.5” HOT-SWAP BAY5.25” device installation EXTERNAL 5.25” DEVICE INSTALLATIONThe plastic drive bay faceplate should pop free A screwdriver may be needed to remove the metal cover plateINTERNAL 2. 5” DEVICE INSTALLATION 2.102. Using the screws provided, secure your 2.5” device 1. Locate the bay at the bottom of the caseSECTION PORTSFRONT I/O AC’97 / HD AUDIO PORTS POWER SWITCH / RESET SWITCH / HARD DISK DRIVE LED CONNECTORS Note Polarity positive and negative does not matter for switchesFront Panel switch leads REWIRING MOTHERBOARD HEADER CONNECTIONSSECTION 4 COOLING SYSTEMStandard fans on the DF-35 A -1 x 120 mm rear TwoCool LED fan INCLUDED FANSB - 1 x 140 mm top TwoCool fan Rear fan control panelFRONT 120 MM WHITE LED FANS Turn this knob to adjust the fanTOP 140 MM TWOCOOL FAN OPTIONAL FANS REAR EXHAUST 120 MM TWOCOOL WHITE LED FANSTo clean the filter Printed in China Copyright 2010 Antec, Inc. All rights reservedAll trademarks are the property of their respective owners