Manuals / Antec / Computer Equipment / Computer Accessories

Antec DF-35 user manual Copyright 2010 Antec, Inc. All rights reserved, Printed in China

Models: DF-35

1 33

Download 33 pages 369 b

Page 33

Image 33

Antec, Inc.

47900 Fremont Blvd.

Fremont, CA 94538

tel: 510-770-1200

fax: 510-770-1288

Antec Europe B.V.

Stuttgartstraat 12

3047 AS Rotterdam

The Netherlands

tel: +31 (0) 10 462-2060

fax: +31 (0) 10 437-1752

Technical Support:

US & Canada

1-800-22ANTEC

customersupport@antec.com

Europe

+31 (0) 10 462-2060

europe.techsupport@antec.com

www.antec.com

All trademarks are the property of their respective owners.

Reproduction in whole or in part without written permission is prohibited.

Printed in China.

Version 1.0.0 06/28/2010

Page 33

Image 33

Antec DF-35 Copyright 2010 Antec, Inc. All rights reserved, All trademarks are the property of their respective owners

Contents

THE ADVANCED GAMING FORCE D F - 3DARKFLEET U S E R M A N U A LDisclaimer DF-35 USER’S MANUALTABLE OF CONTENTS SECTION 1 INTRODUCTION Drive bays Power supply mounts5.25” drive bays 3.5” drive baysCASE SPECIFICATIONS BEFORE YOU BEGIN LOCATING AND POSITIONING YOUR COMPUTER SECTION 2 HARDWARE INSTALLATIONSETTING UP D - Front panel wiring E - I/O panel A - Power supply mounts B - 5.25” drive bay areaC - 3.5” drive bay area with Fleet-Swap SATA bays E D B C ABefore proceeding MOTHERBOARD INSTALLATIONMake sure you have the correct I/O panel. This mismatched I/O panel can cause difficulties down the road4. Install standoffs as needed and put the motherboard back in Lift your motherboard out to install the standoffsStep 5 Screwing in the motherboard after standoffs are installed 3. Now remove your motherboard by lifting it upThe DF-35 can accommodate a standard-size ATX power supply STANDARD ATX POWER SUPPLY INSTALLATIONNote The DF-35 comes with a CPU cutout on the motherboard tray, which PSU resting on the standard PSU mountUse these screws to secure your power supply to the case CABLE MANAGEMENT3. Use the cable ties provided to hold them in place 1. Open the Fleet-ReleaseTM access door INTERNAL 3.5” DEVICE INSTALLATIONOpening the Fleet-Release access door by gently Installing a 3.5” internal deviceEXTERNAL 3.5” DEVICE INSTALLATION Make sure to install screws on the left side…4. Mount any other 3.5” HDD devices accordingly Remove this drive bay coverUSING FLEET-SWAP Fleet-Swap default locationsInsert your drive as shown A - Fleet-Swap SATA and power connectors B - Fleet-Swap bay screws A B ABMoving or removing a Fleet-Swap bay One example of AHCI configuration - your motherboard may vary Loading a Fleet-Swap drive3. Mount any other 3.5” HDD devices accordingly 4. Close the Fleet-ReleaseTM Access Door 3. Grasp the top and bottom of your HDD. Now pull the HDD freeRemoving a Fleet-Swap drive Using the top 2.5” hot-swap drive bay USING THE TOP 2.5” HOT-SWAP BAY5.25” device installation EXTERNAL 5.25” DEVICE INSTALLATIONThe plastic drive bay faceplate should pop free A screwdriver may be needed to remove the metal cover plateINTERNAL 2. 5” DEVICE INSTALLATION 2.102. Using the screws provided, secure your 2.5” device 1. Locate the bay at the bottom of the casePORTS FRONT I/OSECTION AC’97 / HD AUDIO PORTS POWER SWITCH / RESET SWITCH / HARD DISK DRIVE LED CONNECTORS Note Polarity positive and negative does not matter for switchesFront Panel switch leads REWIRING MOTHERBOARD HEADER CONNECTIONSSECTION 4 COOLING SYSTEMStandard fans on the DF-35 A -1 x 120 mm rear TwoCool LED fan INCLUDED FANSB - 1 x 140 mm top TwoCool fan Rear fan control panelTurn this knob to adjust the fan TOP 140 MM TWOCOOL FANFRONT 120 MM WHITE LED FANS OPTIONAL FANS REAR EXHAUST 120 MM TWOCOOL WHITE LED FANSTo clean the filter Copyright 2010 Antec, Inc. All rights reserved All trademarks are the property of their respective ownersPrinted in China

© Copyright 2010 Antec, Inc. All rights reserved.

All trademarks are the property of their respective owners.

Printed in China.