Manuals
/
Antec
/
Computer Equipment
/
Computer Accessories
Antec
DF-35 user manual Introduction
Models:
DF-35
1
4
33
33
Download
33 pages
369 b
1
2
3
4
5
6
7
8
<
>
Specs
Install
One example of AHCI configuration - your motherboard may vary
D - Front panel wiring E - I/O panel
Power Switch / Reset Switch / Hard Disk Drive Led Connectors
Setting Up
Fleet-Swap default locations
Turn this knob to adjust the fan
To clean the filter
Power supply mounts
Page 4
Image 4
S
ECTION
1
I
NTRODUCTION
4
Page 3
Page 5
Page 4
Image 4
Page 3
Page 5
Contents
D F - 3
THE ADVANCED GAMING FORCE
DARKFLEET
U S E R M A N U A L
DF-35 USER’S MANUAL
Disclaimer
TABLE OF CONTENTS
SECTION 1 INTRODUCTION
Power supply mounts
Drive bays
5.25” drive bays
3.5” drive bays
CASE SPECIFICATIONS
BEFORE YOU BEGIN
LOCATING AND POSITIONING YOUR COMPUTER
INSTALLATION
SECTION 2 HARDWARE
SETTING UP
A - Power supply mounts B - 5.25” drive bay area
D - Front panel wiring E - I/O panel
C - 3.5” drive bay area with Fleet-Swap SATA bays
E D B C A
MOTHERBOARD INSTALLATION
Before proceeding
Make sure you have the correct I/O panel. This mismatched I/O panel
can cause difficulties down the road
Lift your motherboard out to install the standoffs
4. Install standoffs as needed and put the motherboard back in
Step 5 Screwing in the motherboard after standoffs are installed
3. Now remove your motherboard by lifting it up
STANDARD ATX POWER SUPPLY INSTALLATION
The DF-35 can accommodate a standard-size ATX power supply
Note The DF-35 comes with a CPU cutout on the motherboard tray, which
PSU resting on the standard PSU mount
CABLE MANAGEMENT
Use these screws to secure your power supply to the case
3. Use the cable ties provided to hold them in place
INTERNAL 3.5” DEVICE INSTALLATION
1. Open the Fleet-ReleaseTM access door
Opening the Fleet-Release access door by gently
Installing a 3.5” internal device
Make sure to install screws on the left side…
EXTERNAL 3.5” DEVICE INSTALLATION
4. Mount any other 3.5” HDD devices accordingly
Remove this drive bay cover
Fleet-Swap default locations
USING FLEET-SWAP
Insert your drive as shown
A B AB
A - Fleet-Swap SATA and power connectors B - Fleet-Swap bay screws
Moving or removing a Fleet-Swap bay
Loading a Fleet-Swap drive
One example of AHCI configuration - your motherboard may vary
3. Mount any other 3.5” HDD devices accordingly
3. Grasp the top and bottom of your HDD. Now pull the HDD free
4. Close the Fleet-ReleaseTM Access Door
Removing a Fleet-Swap drive
USING THE TOP 2.5” HOT-SWAP BAY
Using the top 2.5” hot-swap drive bay
EXTERNAL 5.25” DEVICE INSTALLATION
5.25” device installation
The plastic drive bay faceplate should pop free
A screwdriver may be needed to remove the metal cover plate
2.10
INTERNAL 2. 5” DEVICE INSTALLATION
2. Using the screws provided, secure your 2.5” device
1. Locate the bay at the bottom of the case
FRONT I/O
PORTS
SECTION
AC’97 / HD AUDIO PORTS
Note Polarity positive and negative does not matter for switches
POWER SWITCH / RESET SWITCH / HARD DISK DRIVE LED CONNECTORS
Front Panel switch leads
REWIRING MOTHERBOARD HEADER CONNECTIONS
SYSTEM
SECTION 4 COOLING
INCLUDED FANS
Standard fans on the DF-35 A -1 x 120 mm rear TwoCool LED fan
B - 1 x 140 mm top TwoCool fan
Rear fan control panel
TOP 140 MM TWOCOOL FAN
Turn this knob to adjust the fan
FRONT 120 MM WHITE LED FANS
REAR EXHAUST 120 MM TWOCOOL WHITE LED FANS
OPTIONAL FANS
To clean the filter
All trademarks are the property of their respective owners
Copyright 2010 Antec, Inc. All rights reserved
Printed in China