Manuals / Antec / Computer Equipment / Computer Accessories

Antec DF-35 user manual Case Specifications

Models: DF-35

1 33

Download 33 pages 369 b

Page 6

Image 6

1.2

CASE SPECIFICATIONS

CASE TYPE	Mid Tower

COLOR	Matte black

DIMENSIONS	19.1″ (H) x 7.8″ (W) x 19.1″ (D)
	485 mm (H) x 198 mm (W) x 486 mm (D)
WEIGHT	15.1 lbs / 6.9 kg

COOLING	1 x top 140 mm TwoCool™ fan
	1 x rear white 120 mm TwoCool™ white-bladed fans with white LED
	2 x front variable-speed 120 mm white-bladed LED fans with white LED
	1 x side 120 mm fan for graphics cards (optional)
DRIVE BAYS	6 x internal 3.5	″″

	3 x external 5.25
	1 x top external 2.5” hot swap SATA drive bay
	2 x internal 3.5” Fleet-Swap™ SATA drive bays (position changeable)
	1 x internal bottom-mounted 2.5” SSD bay
EXPANSION SLOTS	7

MOTHERBOARD SIZE	Mini-ITX, microATX, Standard ATX

FRONT I/O PANEL	2 x USB 2.0
	AC’97 / HD Audio In and Out

Page 6

Image 6

Antec DF-35 user manual Case Specifications

Contents

DARKFLEET D F - 3THE ADVANCED GAMING FORCE U S E R M A N U A LDF-35 USER’S MANUAL DisclaimerTABLE OF CONTENTS SECTION 1 INTRODUCTION 5.25” drive bays Power supply mountsDrive bays 3.5” drive baysCASE SPECIFICATIONS BEFORE YOU BEGIN LOCATING AND POSITIONING YOUR COMPUTER INSTALLATION SECTION 2 HARDWARESETTING UP C - 3.5” drive bay area with Fleet-Swap SATA bays A - Power supply mounts B - 5.25” drive bay areaD - Front panel wiring E - I/O panel E D B C AMake sure you have the correct I/O panel. This mismatched I/O panel MOTHERBOARD INSTALLATIONBefore proceeding can cause difficulties down the roadStep 5 Screwing in the motherboard after standoffs are installed Lift your motherboard out to install the standoffs4. Install standoffs as needed and put the motherboard back in 3. Now remove your motherboard by lifting it upNote The DF-35 comes with a CPU cutout on the motherboard tray, which STANDARD ATX POWER SUPPLY INSTALLATIONThe DF-35 can accommodate a standard-size ATX power supply PSU resting on the standard PSU mountUse these screws to secure your power supply to the case CABLE MANAGEMENT3. Use the cable ties provided to hold them in place Opening the Fleet-Release access door by gently INTERNAL 3.5” DEVICE INSTALLATION1. Open the Fleet-ReleaseTM access door Installing a 3.5” internal device4. Mount any other 3.5” HDD devices accordingly Make sure to install screws on the left side…EXTERNAL 3.5” DEVICE INSTALLATION Remove this drive bay coverUSING FLEET-SWAP Fleet-Swap default locationsInsert your drive as shown A - Fleet-Swap SATA and power connectors B - Fleet-Swap bay screws A B ABMoving or removing a Fleet-Swap bay One example of AHCI configuration - your motherboard may vary Loading a Fleet-Swap drive3. Mount any other 3.5” HDD devices accordingly 4. Close the Fleet-ReleaseTM Access Door 3. Grasp the top and bottom of your HDD. Now pull the HDD freeRemoving a Fleet-Swap drive USING THE TOP 2.5” HOT-SWAP BAY Using the top 2.5” hot-swap drive bayThe plastic drive bay faceplate should pop free EXTERNAL 5.25” DEVICE INSTALLATION5.25” device installation A screwdriver may be needed to remove the metal cover plate2. Using the screws provided, secure your 2.5” device 2.10INTERNAL 2. 5” DEVICE INSTALLATION 1. Locate the bay at the bottom of the casePORTS FRONT I/OSECTION AC’97 / HD AUDIO PORTS Front Panel switch leads Note Polarity positive and negative does not matter for switchesPOWER SWITCH / RESET SWITCH / HARD DISK DRIVE LED CONNECTORS REWIRING MOTHERBOARD HEADER CONNECTIONSSYSTEM SECTION 4 COOLINGB - 1 x 140 mm top TwoCool fan INCLUDED FANSStandard fans on the DF-35 A -1 x 120 mm rear TwoCool LED fan Rear fan control panelTurn this knob to adjust the fan TOP 140 MM TWOCOOL FANFRONT 120 MM WHITE LED FANS REAR EXHAUST 120 MM TWOCOOL WHITE LED FANS OPTIONAL FANSTo clean the filter Copyright 2010 Antec, Inc. All rights reserved All trademarks are the property of their respective ownersPrinted in China