Arcam AVR350 manual Remote control

Remote control

The CR80 remote control is a multi-function unit that controls the AVR350 and up to seven other devices. The instructions on this page only refer to the control of the Arcam AVR350.

For information on using the remote control for other devices, and a full list of features, see the instruction booklet supplied with the CR80.

Source selection
DVD – DVD input
SAT – Satellite input	SET
VCR – toggle between the VCR and PVR inputs
CD – CD player input
TAPE – Tape (monitor) input
AV – AV input	CBL
MCH – DVD-A (multi-channel) input
FM – FM tuner input	SAT
AM – AM tuner input

Press the relevant button once to select input;

Device selection

IMPORTANT: Press the ‘AMP’ button first to operate the AVR350.

			On/Stand-by
			This allows the AVR350 to be put into and
			taken out of stand-by remotely.
SELECT DEVICE			If you do not wish to put Zone 2 into stand-
			by at the same time as the main zone, press
DVD	VCR	TV	and hold the stand-by button on the remote
			control for about 3 seconds.
CD	AMP	AUX
			THX

English

press and hold to select the analogue input if a1 DVD digital input is present.

	4 CD
	7 TUN
MUTE
Press once to mute the main system. Press again	MUTE
(or use VOL +/–) to un-mute.
VOLUME +/–
Adjusts the volume.	VOL
	GUIDE
MODE

2 SAT	3 VCR
5 AUX	6 TAPE
8 AV	9 MCH
0 FM	AM
LAST
THX
SLEEP
FX	CH
A–B
SUB
	EXIT

In Zone 2, use this button to enable ‘Follow Zone 1’ mode.

Note that the AVR350 does not support THX processing.

FX (DSP effects mode)

Use this button to cycle through effects modes for two-channel sources.

SUB (Subwoofer trim)

Allows a temporary trim of the subwoofer level. Press SUB, then adjust using the D and E buttons.

Use this button to cycle through available MODE

surround modes.

INFO

Press to change the RDS display mode for the	INFO
tuner.

OPEN

OK

MENU

Navigation buttons

Arrow buttons allow navigation around the menus on the AVR350.

Confirm selection by pressing OK.

MENU

Press to select the OSD Main menu.

Press and hold for more than two seconds to select the ‘Set-up Menu Index’.

P- / P+ (Tune/Preset Down/Up)

If the tuner is in preset mode, then these buttons decrease/increase the preset selection. If the tuner is in tune mode, then these buttons decrease/increase the selected frequency.

SYN (Lip sync)

Press once to adjust the Lip sync audio delay. Use the D and E navigation buttons.

Press again to exit the Lip sync function.

DIS (Display)

Press to cycle through Off/Dim/Bright illumination of the front panel display

TRM (Speaker trim)

P.MODE	SUBT	TITLE	MENU
P –	P +	TM	FAV
ZOOM	AUDIO	MEM	RETURN
TST	SYN	DYN	SLP
ANGLE	SETUP	STATUS	SEARCH
DIS	TRM	1	2

CR80

TM

Tuning mode: press this button to toggle between ‘preset’ and ‘tuning’ modes on the tuner.

DYN/MEM

Used to store a radio station in a preset. Press once to enter store mode; use the P+/P- buttons to select the preset to use, then press this button again to confirm the selection.

1/STATUS

Press this button to toggle between FM ‘stereo mute’ and ‘mono’ on the tuner.

The other buttons in this area are used for DVD control and do not effect the AVR350.

Press to display the OSD Speaker trim level
menu. TRM allows temporary adjustment of
speaker levels, using the navigation buttons.
	NOTE
Press again to exit the ‘Speaker Trim’ function.
	Remember to install the two AA batteries supplied	before
	trying to use your remote control.	AVR350
		E-19