Manuals / Ariens / Lawn and Garden / Snow Blower

Ariens quick start Quick Start Guide, Deluxe-Track 28 921023 s/n 75000 & up

Models: 921023

1 30

Download 30 pages 55.33 Kb

Page 1

Quick Start Guide

Quick Start Guide

Deluxe-Track 28 (921023 s/n 75000 & up)

•Step 1: Assemble Handlebars

•Step 2: Install Discharge Chute

•Step 3: Install Discharge Chute Crank

•Step 4: Install Remote Deflector Control

•Step 5: Check Function of Dual Handle Interlock

•Step 6: Check Track Tension

•Step 7: Adjust Skid Shoes

•Step 8: Check Auger Gearcase Oil

•Step 9: Check Engine Crankcase Oil

•Step 10: Fill Engine Fuel Tank

•Step 11: Start Engine

•Step 12: Stop Engine

READ AND UNDERSTAND ALL INSTRUCTION, WARNING, AND DANGER LABELS. IMPORTANT: READ OPERATOR’S MANUAL AND ENGINE MANUAL THOROUGHLY AND FOLLOW THE IMPORTANT SAFE OPERATION PRACTICES BEFORE OPERATING.

Image 1

Ariens quick start Quick Start Guide, Deluxe-Track 28 921023 s/n 75000 & up

Contents

Deluxe-Track 28 921023 s/n 75000 & up Quick Start GuideNot attached Step One Assemble HandlebarsNOTE This slide applies to UNATTACHED handlebars ONLY Step One Assemble Handlebars Unfold Lower HandlebarNOTE This slide applies to UNATTACHED handlebars ONLY Step One Assemble Handlebars Attach Upper Handlebar Assembly1. Hook Spring end of attachment control cable to the clutch arm Step One Assemble Handlebars Attach Control CablesNOTE Make sure the cable remains in the groove of the pulley NOTE This slide applies to UNATTACHED handlebars ONLYNOTE This slide applies to UNATTACHED handlebars ONLY Step One Assemble Handlebars Unfold Upper HandlebarNOTE This slide applies to UNATTACHED handlebars ONLY Step One Assemble Handlebars Connect Headlight Wire HarnessNOTE Trigger cable assembly comes attached to the Sno-thro unit Step One Assemble Handlebars Install Trigger CableNOTE This slide applies to UNATTACHED handlebars ONLY NOTE This slide applies to ATTACHED handlebars ONLY Step One Assemble Handlebar2. Remove mounting hardware from auger housing Step Two Install Discharge Chute1. Grease underside of discharge chute ring if not already greased Step Three Install Discharge Chute Crank Step Four Install Remote Deflector Control Cable Step Five Check Function of Dual Handle Interlock Step Six Check Track Tension Step Seven Adjust Skid Shoes Check oil level in auger gearcase Step Eight Check Auger Gearcase Oilsee Check Auger Gearcase in Owners Manual IMPORTANT The engine is shipped with oil Step Nine Check Engine Crankcase Oilin crankcase. Refer to Engine Manual for detailed instructions Fill fuel tank. DO NOT OVERFILL! See Step Ten Fill Engine Fuel TankFILLING FUEL TANK in Owners ManualStep Eleven Starting the Engine Move the throttle control lever to the fast position Starting Engine / Step A ThrottleTurn the fuel shut- off valve to the ON position Starting Engine / Step B Fuel ValveInsert the key and turn to the ON/START position Starting Engine / Step C KeyStarting Engine / Step D Choke NOTE Choke is usually unnecessary when restarting a warm engineTurn the choke control knob to the choke position Starting Engine / Step E Prime NOTE Priming is usually unnecessary when restarting a warm enginePush the primer two times. Be sure to cover vent hole on primer bulb NOTE If the engine does not start after repeated attempts, go to Starting Engine / Step F Manual Startor call BRIGGSandSTRATTON.COMStarting Engine / Step F Electric Start Starting Engine / Step G Electric Start Starting Engine / Step H Warm up Step Twelve Stopping the Engine Additional Resources For issues concerning engine, please contact Briggs and StrattonRefer to Owners Manual and Engine Manual Contact Ariens Company E-mail info@ariens.com