Manuals / Brands / Computer Equipment / Network Card / Asante Technologies / Computer Equipment / Network Card

Asante Technologies ASANTE MacCon Family Ethernet Network Cards for the Macintosh manual 23 2

1 65

Download 65 pages, 711.2 Kb

Chapter 2

A-1

Appendix A

23 2

Technical Speciﬁcations

MacCon Speciﬁcations

The speciﬁcations for the Asanté MacCon cards are given below.

Systems supported Macintosh SE, SE/30, IIsi, LC family, Color Classic,

Quadra, MacII (NuBus) family, Centris, and Per-

forma computers with an available expansion slot

Standards supported IEEE 802.3 Ethernet speciﬁcations for thick

(10Base5), thin (10Base2), and Unshielded

Twisted-Pair (10BaseT) media; Phase 1 and Phase

2 EtherTalk. Register-level compatible with Apple

Computer’s Ethernet cards

Software supported AppleShare, Novell NetWare for Macintosh, 3Com

3+Open, 3Com 3+Share, Sitka TOPS, DEC Path-

works, A/UX and other popular network software

Protocols supported AFP, TCP/IP, DecNet, and LAT

Math co-processor Motorola 68882 PLCC math co-processor available

for MacCon IIsi, 30i, and LC cards

Address selection

(IIsi only)

4 user-selectable slot addresses: 9, A, B and E

Power requirements +5V @ 1300 mA max. (thin)

+5V @ 1000 mA max (UTP)

+12V @500 mA max (thick)

+5V @800 mA max. (LC Series)

Operating temperature 0˚ to 50˚ C

Relative humidity: 10% - 90%, non-condensing

Warranty 5 years

MacConi Appendix A Page 1 Friday, August 23, 1996 10:06 AM

Contents

Main Page Page Page Asking for assistance Technical support hours Tell us what you think Table of Contents Page List of Figures Chapter 1 and Introducing the Asant MacCon Cards Summary of MacCon Card Features The Math Co-processor Option Asant EtherTalk Installer Software Installing Asant MacCon Cards Checking the Requirements Preparing for the Installation Observing the Safety Rules The MacCon NuBus Card Installing the MacCon NuBus Card Page Installing the MacCon 610 Card Page Page Installing a MacCon LC Card Page Page Page Installing the MacCon3 IIsi and MacCon 30i Cards Setting the Cable Type on the Daughter Card Video Options Setting the Slot Address for Two Cards Installing the Math Co-processor Installing in a Macintosh IIsi 1 2 3 4 5 6 Page Page Page 3 4 5 6 7 Installing a MacCon+ SE Card in a Macintosh SE Setting the Cable Type on the Daughter Card 1 2 3 4 5 6 7 8 9 10 11 12 Connecting the Macintosh to the Network 1 2 1 2 3 Installing the EtherTalk Software 1 2 3 4 5 Accessing Network Services 1 2 3 4 5 Chapter 3 IP Addressing Asant SNMP MacAgent Introduction Requirements Asant SNMP MacAgent and the TCP/IP Protocol Accessing Asant MacAgent MIB AsantView In-Band Network Management Software Installing SNMP MacAgent Page Conguring SNMP MacAgent Asant SNMP Conguration Parameters AsantView Network Management Station Other Network Management Software Chapter 4 Changing from EtherTalk to LocalTalk Using TroubleShooter and ADLS Diagnostic Software Running TroubleShooter Diagnostics Starting TroubleShooter Diagnostics Page Page Page If a test fails Page Page Chapter 5 Troubleshooting Running TroubleShooter Macintosh IIsi with a PDS Slot Installing the Math Co-processor Option Other Tips Page Page Appendix A The specications for the Asant MacCon cards are given below. MacCon Specications 23 2 Technical Specications Ethernet Address MacCon LEDs The table below lists the Ethernet specications. Ethernet Specications Connector Pin-outs AAUI Connector The following table describes the AUI connector pinouts. RJ-45 Connector