Manuals / Brands / Computer Equipment / Network Card / Asus / Computer Equipment / Network Card

Asus CUVL-VM NOTE:, 6. SOFTWARE REFERENCE, ASUS CUVL-VMUser’s Manual, do not place jumper caps over these pins, CPU Fan, Power Supply Fan, and Chassis Fan Connectors

1 86

Download 86 pages, 2.46 Mb

3.HARDWARE SETUP

6)CPU Fan, Power Supply Fan, and Chassis Fan Connectors (3-pin CPU_FAN/PWR_FAN/CHA_FAN)

The three fan connectors support cooling fans of 350mA (4.2 Watts) or less. Orient the fans so that the heat sink fins allow airflow to go across the onboard heat sink(s) instead of the expansion slots. The fan wiring and plug may vary depending on the fan manufacturer. The red wire should be positive while the black should be ground. Connect the fan plug to the board taking into consideration the polarity of the connector.

NOTE: Use the “ Rotation” signal only with a specially designed fan with a rotation signal. The Rotations Per Minute (RPM) can be monitored using ASUS PC Probe (see 6. SOFTWARE REFERENCE).

WARNING! The CPU and/or motherboard will overheat if there is no airflow across the CPU and onboard heatsinks. Damage may occur to the motherboard and/or the CPU fan if these pins are incorrectly used. These are not jumpers,

do not place jumper caps over these pins.

Rotation

+12V CHA_FAN

GND

NC +12V GND

PWR_FAN

GND

+12V

Rotation CPU_FAN

CUVL-VM

CUVL-VM 12-Volt Cooling Fan Power

Connectors

3. H/W SETUP

ASUS CUVL-VM User’s Manual

31

Contents

Page ASUS CUVL-VM 1.02 E720 March ASUS CUVL-VMUser’s Manual ASUSTeK COMPUTER INC. (Asia-Pacific) ASUS COMPUTER INTERNATIONAL (America) ASUS COMPUTER GmbH (Europe) Page Page Page 1.1How This Manual Is Organized 1.2 Item Checklist 2.1ASUS CUVL-VMMotherboard 2.1.1 Specifications Enhanced ACPI and Anti-Boot Virus Protection: Onboard Audio: 2.1.2Performance 2.1.3Intelligence 2.2Motherboard Components 2.2.1Component Locations 3.1Motherboard Layout 3.2Layout Contents 3.3Hardware Setup Procedure 3.4Motherboard Settings Motherboard Features Settings (DIP Switches - SW1) 1)CPU External Frequency Selection (SW1 Switches 1–4) 2)Clear RTC RAM 3.5System Memory 3.5.1 General DIMM Notes 3.5.2Memory Installation 3.6Central Processing Unit (CPU) 3.6.1CPU Installation 3.7Expansion Cards 3.7.1 Installing an Expansion Card 3.7.2Assigning IRQs for Expansion Cards 3.8Connectors 3.8.1External Connectors 4)Parallel Port Connector (Burgundy 25-pinPRINTER) Onboard Parallel Port 4.4.2 I/O Device Configuration) NOTE 5)Serial Port Connector (Teal/Turquoise 9-pinCOM1) 7)Game/MIDI Connector (Gold 15-pinGAME_AUDIO) (optional) 8)Audio Connectors (Three 1/8” AUDIO) (optional) Line Out Line In Mic 3.8.2Internal Connectors 3)Primary (Blue) / Secondary IDE Connectors (40-1pin IDE1/IDE2) NOTES: TIP: 4)Wake-On-LANConnector (3-pinWOL_CON) 4.5.1 Power Up Control 5)Wake-On-RingConnector (2-pinWOR) CPU Fan, Power Supply Fan, and Chassis Fan Connectors 6. SOFTWARE REFERENCE do not place jumper caps over these pins 7)Standard Infrared Module Connector (5-pinIR) 8)USB Header (10-1pin USBPORT) 10)Serial Port 2 Connector (10-1pin COM2) 11)ATX Power Supply Connector (20-pinblock ATXPWR) 12)System Power LED Lead (3-1pin PWR.LED) 13)System Warning Speaker Lead (4-pinSPEAKER) 14)System Management Interrupt Lead (2-pinSMI) 15)ATX Power Switch / Soft-OffSwitch Lead (2-pinPWR.SW) 16)Reset Switch Lead (2-pinRESET) 3.9Starting Up the First Time 4.1Managing and Updating Your BIOS 4.1.1 Upon First Use of the Computer System 1. Save Current BIOS to File Save Current BIOS To File A:\XXX-XX.XXX SETUP BIOS 4.1.2Updating BIOS Procedures Page 4.2BIOS Setup Program 4.2.1BIOS Menu Bar 4.2.2 Legend Bar General Help Saving Changes and Exiting the Setup Program Scroll Bar Sub-Menu 4.3Main Menu 4.3.1Primary & Secondary Master/Slave [User Type HDD] Translation Method [LBA] Cylinders Type Translation Method Head Sector CHS Capacity Maximum LBA Capacity Multi-SectorTransfers [Maximum] 4.3.2 Keyboard Features Language [English] Supervisor Password [Disabled] / User Password [Disabled] A Note about Passwords Forgot the Password 3.4 Motherboard Settings 4.4Advanced Menu USB Legacy Support [Auto] OS/2 Onboard Memory > 64M [Disabled] 4.4.1Chip Configuration SDRAM Active to Precharge Time [6T] SDRAM Data Driving Strength [Auto] Read Around Write [Enabled] CPU-DRAM Back-BackTransaction [Enabled] Delayed Transaction [Disabled] AGP Drive Strength [Auto] Graphics Aperture Size [64MB] On-ChipVGA Shared Memory Size [8MB] Video Memory Cache Mode [UC] Onboard PCI IDE Enable [Both] 4.4.2I/O Device Configuration Parallel Port Mode [ECP+EPP] ECP DMA Select [3] ECP Parallel Port Mode Onboard Peripheral Resource Control 4.4.3PCI Configuration 4.4.4 Shadow Configuration 4.5Power Menu Video Off Option [Suspend ->Off ] Video Off Method [DPMS OFF] HDD Power Down [Disabled] Suspend Mode [Disabled] PWR Button < 4 Secs [Soft Off] 4.5.1Power Up Control 4.5.2 Hardware Monitor 4.6Boot Menu Boot Sequence Plug & Play O/S [No] Reset Configuration Data [No] Boot Virus Detection [Disabled] Quick Power On Self Test [Enabled] Boot Up Floppy Seek [Enabled] 4.7Exit Menu Exit Saving Changes Exit Discarding Changes Load Setup Defaults Discard Changes Save Changes Page 5.1Operating Systems 5.1.1 Windows 98 First Time Installation 5.2 CUVL-VMMotherboard Support CD 5.2.1 Installation Menus 5.2.2 Applications SETUP S/W RealTek RTL8139C PCI Fast Ethernet NIC Driver: Intel LDCM 6.10.0.17 Administrator Setup: Intel LDCM 6.10.0.17 Client Setup: ASUS BIOS Flash Utility for LDCM 6.10.0.17: 6.1ASUS PC Probe 6.1.1 Starting ASUS PC Probe 6.1.2Using ASUS PC Probe Settings History Fan Control Information Hard Drives Memory Device Summary DMI Explorer Utility Execute Program 6.1.3ASUS PC Probe Task Bar Icon Page 7.1PCI-L101Fast Ethernet Card 7.1.1 Features 7.1.2 Software Driver Support 7.1.3 Question and Answer 7.2 Glossary Boot Bus Master IDE Byte (Binary Term) COM Port Concurrent PCI LPT Port (Line Printer Port) MMX OnNow PC100 PCI Bus (Peripheral Component Interconnect Local Bus) ROM (Read Only Memory) SCSI (Small Computer System Interface) SDRAM (Synchronous DRAM) SPD for SDRAM module SSE (Streaming SIMD Extensions)