IDE Connector | Asus P1P5945GCBLK instruction

2IDE connectors (40-1 pin PRI _IDE)

The onboard IDE connectors are for Ultra DMA 100/66/33 signal cable(s). There are three connectors on each Ultra DMA 100/66/33 signal cable: blue, black, and gray. Connect the blue connector to the motherboard’s IDE connector, then select one of the following modes to configure your device(s).

PRI_IDE

PIN1

IDE Connector

NOTE: Orient the red markings (usually zigzag) on the ID ribbon cable to PIN 1.

	Drive jumper	Mode Cable of	Cable connector
	setting	device(s)
Single device	Cable-Select or	-	Black
	Master
Two devices	Cable-Select	Master	Black
		Slave	Gray
	Master	Master	Black or gray
	Slave	Slave

•Pin 20 on the IDE connector is removed to match the covered hole on the Ultra DMA cable connector. This prevents incorrect insertion when you connect the IDE cable.

•Use the 80-conductor IDE cable for Ultra DMA 100/66/33 IDE devices.

If any device jumper is set as “Cable-Select”, make sure all other device jumpers have the same setting.

4-	Chapter 4: Motherboard info

Image 51

Asus P1P5945GCBLK manual IDE Connector

Contents

P1-P5945G/P2-P5945G E2798 First Edition October Table of contents Motherboard Info Chapter Bios InformationIntroduction Motherboard layout Jumpers Connectors Chapter Starting up USB Configuration CPU Configuration Chipset Federal Communications Commission Statement Canadian Department of Communications StatementThis class B digital apparatus complies with Canadian Ices Safety information Electrical safetyOperation safety This guide contains the following parts System introduction About this guideAudience How this guide is organized Conventions used in this guide Where to find more information System package contents System introduction Welcome Front panelClose Open Rear panel Power connector Port Headset Channel Audio 2, 4, 6 or 8-channel configuration CPU fan and heatsink assembly Internal componentsAsus motherboard Dimm sockets Basic installation Tool Basic components to installPreparation Before you proceed Removing the chassis cover and front panel assembly Central Processing Unit CPU Removing the storage drive assemblyInstalling CPU To install a CPU Locate the CPU socket on the motherboard Retention tab Load lever Removing and Installing the CPU fan and heatsink assembly Memory configurations Installing a Dimm Size Vendor Model Sides Component Qualified Vendors Lists QVL DDR2-533 DDR2-667 Installing a DDR2 Dimm Removing a DDR2 DimmRemove the Dimm from the socket PCI slots Expansion card installationLift the PCI riser card assembly to remove Expansion slotsPage IRQ assignments for this motherboard Standard interrupt assignmentsPage Asus Pundit P1-P5945G/P2-P5945G Installing the foot stand Reinstalling the front panel cover Reinstalling the cover Starting up Support CD information Installing an operating systemPowering up Press the system power button to enter the OS Running the support CD Utilities menu Asus Contact information Asus PC Probe Installing PC ProbeUsing PC Probe Software information Sensor alert Preferences Changing the monitor panels position Hardware monitor panels DMI browser WMI browser Usage PCI browser Memory usage Configuring PC Probe InfoMotherboard Motherboard layout Introduction Clear RTC RAM Clrtc Jumpers USB Device Wake Up Sata Connectors Connectors IDE Connector CPU FAN Connector CPU Fan connector 3-pin Cpufan ATX Power Connector Backaudio Back audio connector 20-1 pin BackAudio Connector System Panel Connector Bios setup Asus EZ Flash 2 utility Managing and updating your Bios Copying the current Bios To copy the current Bios file using the Afudos utilityAfudos utility Updating the Bios file To update the Bios file using the Afudos utilityUtility verifies the file and starts updating the Bios Recovering the Bios from a floppy disk Asus CrashFree Bios 2 utility Recovering the Bios from the support CD Installing Asus Update Asus Update utility Updating the Bios through the Internet Updating the Bios through a Bios file Bios setup program Navigation keys Bios menu screenConfiguration Menu bar Pop-up window Configuration fieldsMenu items Sub-menu items Allows you to set the system time Main menuSystem Time System Date Day xx/xx/xxxx Block Multi -sector Transfer Auto LBA/Large Mode AutoPrimary and Third IDE Master/Slave Type Auto IDE Configuration IDE Detect Time Out System Information ProcessorSystem Memory JumperFree Configuration Advanced menuAI Overclocking Auto Overlock Options Overlock 5% USB ConfigurationUSB Function Enabled USB 2.0 Controller Enabled USB Mass Storage Device USB 2.0 Controller Mode HiSpeedBios Ehci Hand -off Enabled USB Mass Storage Reset Delay 20 Sec CPU Configuration Ratio Cmos SettingMicrocode Updation Enabled Enhanced C1 Control Auto Max Cpuid Value Limit DisabledExecute Disable Function Disabled Hyper Threading Technology Disabled Chipset Configure Dram Timing by SPD Enabled Onboard Devices Configuration Serial Port1 Address 3F8/IRQ4 Plug and Play O/S No PCI Latency TimerPalette Snooping Disabled PCI PnP Acpi 2.0 Support No Power menuSuspend Mode Auto Acpi Apic Support Enabled Power On By External Modems Disabled Power Button Mode On/OffRestore on AC Power Loss Power Off Power On By RTC Alarm Disabled Power On By Pcie Devices Disabled Power On By PS/2 Keyboard DisabledPower On By PS/2 Mouse Disabled CPU Fan Speed xxxxRPM or N/A or Ignored AI Quiet DisabledCPU Temperature xxxC/xxxF MB Temperature xxxC/xxxF CPU Q-Fan Control Disabled 1st ~ 4th Device USBGeneric 2.0Re Boot menuBoot Device Priority Removable Drives Bootup Num-Lock On Quick Boot EnabledFull Screen Logo Enabled Add On ROM Display Mode Force Bios Interrupt 19 Capture Disabled Change Supervisor PasswordSecurity No Access prevents user access to the Setup utility User Access Level Full AccessChange User Password Clear User Password Password Check Setup Exit menuExit & Save Changes Load Setup Defaults Exit & Discard ChangesDiscard Changes Asus P1 -P5945G/P2 -P5945G