|
|
| Data Capture | |
|
|
| for Workforce | |
|
|
| in Motion | |
|
|
|
|
|
|
|
|
|
|
|
| For each step: |
|
|
|
| {(Bit 6: Blue LED 1) (Bit 5: Red LED 1) (Bit 4: Green LED 1) (Bit 2: Blue LED 0) (Bit 1: Red |
| |
|
| LED 0) (Bit 0: Green LED 0)} |
| |
|
| {Buzzer frequency, 0 – 0xFF * 50Hz = 0 – 12750Hz} |
| |
|
| {Delay until next step, in tenth of seconds} |
| |
|
|
|
|
|
| Response | 1 byte: {(Bit 0: Success)} |
|
|
|
|
|
|
|
|
|
|
|
|
| Code ID |
|
| |
|
|
|
|
|
| Description | Play Signal |
|
|
|
|
|
|
|
| Payload | 2 bytes: |
|
|
|
| {Signal number, 0 - 3} |
|
|
|
| {Number of loops, 0 – 0xFE, 0xFF = infinity} |
| |
|
|
|
|
|
| Response | 1 byte: {(Bit 0: Success)} |
|
|
|
|
|
|
|
|
|
|
|
|
| Code ID |
|
| |
|
|
|
|
|
| Description | Stop Signal |
|
|
|
|
|
|
|
| Payload | 1 byte: |
|
|
|
| {Signal number, 0 – 3} |
|
|
|
|
|
|
|
| Response | 1 byte: |
|
|
|
| {(Bit 0: Success)} |
|
|
|
|
|
|
|
| The list of MMI signals is: |
|
| |
| IHM_SIGNAL_CAPTURE_READ : | 0 |
| |
| IHM_SIGNAL_CAPTURE_ACK : | 1 |
| |
| IHM_SIGNAL_CAPTURE_NAK : | 2 |
| |
| IHM_SIGNAL_CAPTURE_LOST : | 3 |
| |
|
|
|
|
|
| Code ID |
|
| |
|
|
|
|
|
| Description | Get Beeps mode |
|
|
|
|
|
|
|
| Payload |
|
|
|
|
|
|
|
|
| Response | 1 byte: |
|
|
|
| {(Bit 0: Beep level 0=low, 1=high) |
| |
|
| (Bit 1: Read beep) |
|
|
|
| (Bit 2: ACK beep)} |
|
|
|
|
|
|
|
|
|
|
|
|
| Code ID |
|
| |
|
|
|
|
|
| Description | Set Beeps mode |
|
|
|
|
|
|
|
| Payload | 1 byte: |
|
|
|
| {(Bit 0: Beep level; 0=low, 1=high) |
| |
|
| (Bit 1: Read beep) |
|
|
|
| (Bit 2: ACK beep) |
|
|
|
| (Bit 7 = 0: ACK beep config select, =1: ACK beep config deselect) |
| |
|
| (Bit 6 = 0: Read beep config select, =1: Read beep config deselect) |
| |
|
| (Bit 5 = 0: Beep level config select, =1: Beep level config deselect)}} |
| |
|
|
|
|
|
BaracodaPencil 2 – Communication Protocol v1.3 | - 12 - |
