Barco R5976934 12.5.4 Tilting

12. Accessories

Barco - LC series - R5976934 - user's manual - Revision 08 - April 2008_____________________________________________________________________________________ 12-15

12.5.4 Tilting

To tilt the monitor, the two top screws connecting the rear plate and the front plate have to be removed.

If you want to change the tilt angle of the monitor,

first uninstall the monitor!!

Never loosen the screws for setting the tilt an gle when the monitor is still attached to the

tiltable wall mount!

• Uninstall the monitor!

• Use the included allen wrench 4mm to loosen the left and the right top screws.

• Tilt the front plate to the desired degree.

• Reattach the screws.

• Re-install the monitor.

For security reasons, the two top screws to ad just the tilting angle are applied with a

center pin and thus require a special tool. Therefore the allen wrench 4mm is included

which feature a center hole for the pin.

Contents

Main User's manual LC series Page Document History Page WARRANTY STATEMENT WARRANTY STATEMENTWARRANTY STATEMENT WARRANTY STATEMENT Hardware warranty Software warranty Revision sheet Barco Control Room GmbH Contents Page Page Page Page 1 Preliminary Remarks 1.1 How this manual is organized 1.2 Styles and symbols 1.3 Safety information 1.3.1 Safety on installation Page Page 1.3.2 Safety on servicing 1.3.3 Safety on shipping 1.3.4 Precautions Do not spray 1.3.5 Malfunction or Trouble 1.3.6 Unpacking of devices 1.3.7 Modification of devices 1.3.8 Disposal or handing over to a new owner 1.3.9 Exemptions Page Page 2.1 Unpacking 2.2 Installation 2.2.1 Accessories 2.2.2 Mounting of the table stand (optional) Lay the monitor upside down on a clean(!) surface, bottom edge flush with e.g. edge of the table. Page 2.2.3 Dimensions of the 42" monitor: 2.2.4 Dimensions of the 47" monitor: 2.2.4.1 Front view 2.2.4.2 Side view and rear view: 2.3 Examining the monitor 2.3.1 Front view 2.3.2 Side view 2.3.3 Rear view 2.4 Cabling Connect the video and RGB sources with the respective interface using the included cables. 2.5 Switching on and off 2.6 Inserting batteries into the Infrared remote control unit Page 3.1 Display of choice 3.2 Technology 3.2.1 Principle of LCD technology Page Page 4.1 General 4.1.1 The push buttons 4.1.2 The IR remote control unit 4.2 Terminology of the RCU controls 4.3 Functions available with the IR Remote Control Unit 4.3.1 Displaying a monitor address 4.3.2 Baud rate setting 4.3.3 The function keys 4.3.4 Picture controls with direct access. 4.3.5 Audio controls with direct access. Page 5.1 General 5.1.1 Navigation and adjustment 5.2 Activating the OSD Press the ADJ key to activate the OSD - Press 7 to activate the OSD Use the left and right cursor key to select a Use the push buttons 3, 4 to select a Menus without a submenu will turn blue Menus with a sub menu will turn blue and Menus without a submenu will turn 5.3 The signal menu (first and second input) Press the ADJ key input1 input2 Press 7 Use the left and right cursor keys to navi- Press 3 and 4 to navigate to the Press Enter to select Press 2 to select Use the left ad right cursor keys to navi- 5.3.1 Display 5.3.1.1 Brightness Use the up and down cursor keys to navigate to Press 5 and 6 to navigate to Brightness Use 3 and 4 to increase/decrease the value in 5.3.1.2 Contrast 5.3.1.3 Hue 5.3.1.4 Saturation 5.3.1.5 Flesh tone 5.3.1.6 Black level (only available for analog RGB) The black level is the deepest black of the monitor. 5.3.2 Position 5.3.2.1 Zoom button is activated. (The reverse operation is Use the up and down cursor keys to navigate to Press 5 and 6 to navigate to Zoom Use the left and right cursor keys to select one 5.3.2.3 Zoom Vertical Pan 5.3.2.4 Vertical 5.3.2.5 Horizontal 5.3.3 PIP control Page 5.3.3.1 PIP Mode Use the up and down cursor keys to navigate to Press 5 and 6 to navigate to PIP Mode Use the left and right cursor keys to select one Use 3 and 4 to select one of the options Off, 5.3.3.2 PIP Size 5.3.4 Combination of signals for main image and PiP/PaP 5.3.5 Image 5.3.5.1 Analog RGB Scaling Use the up and down cursor keys to navigate to Press 5 and 6 to navigate to Scaling Use the left and right cursor keys to select one Use 3 and 4 to select one of the options Native, Auto Adjust Use the key FREEZE on the remote control unit to immediately start Auto Adjust. Use the up and down cursor keys to navigate to Press 5 and 6 to navigate to Auto Adjust Use the left and right cursor keys to select Use 3 and 4 to select Select Phase Use the up and down cursor keys to navigate to Press 5 and 6 to navigate to Phase Use 3 and 4 to increase/decrease the value in Clock Page Scaling Adaptive Deinterlacing Noise Reduction Noise is generally visible as "snow", or small dots that make the picture look fuzzy, With the amount of noise attenuation can be specified. Angle Filtering Use the up and down cursor keys to navigate to Sharpness The edges are localized and the contrast between neighboring pixels enhanced. Use the up and down cursor keys to navigate to Press 5 and 6 to navigate to Sharpness Use 3 and 4 to increase/decrease the value in 5.3.6 Color 5.3.6.1 Gamma Correction 5.3.6.2 Color Temperature Use the up and down cursor keys to navigate to Use the 5 and 6 to select Red, Green, Blue Use 3 and 4 to increase/decrease the value in 5.4 OSD setting menu 5.4.1 Vertical Use the up and down cursor keys to navigate to Press 5 and 6 to navigate to Vertical Use 3 and 4 to increase/decrease the value in 5.4.2 Horizontal 5.4.4 Time out Use the up and down cursor keys to navigate to Press 5 and 6 to navigate to Time out Use 3 and 4 to increase/decrease the value in 5.4.5 OSD Zoom 5.5 Audio setting menu 5.5.1 Volume Use the up and down cursor keys to navigate to Press 5 and 6 to navigate to Volume Use 3 and 4 to increase/decrease the value in 5.5.2 Balance 5.5.4 Treble 5.6 Display parameter setting menu Use the up and down cursor keys to navigate to Press 5 and 6 to navigate to the desired parame- Use the left and right cursor keys to activate Use 3 and 4 to activate the desired value 5.6.1 Set display address Use the up and down cursor keys to navigate to Press 5 and 6 to navigate to Set display address Use 3 and 4 to increase/decrease the address in 5.6.2 Baud rate 5.6.3 Light Sensor Use the up and down cursor keys to navigate to Press 5 and 6 to navigate to Light Sensor Use the left and right cursor keys to select one Use 3 and 4 to select one of the options Off, On 5.6.4 Lower brightness level 5.6.6 Auto Source Selection When Auto Source Selection is on, the system searches for a valid input source signal. Use the up and down cursor keys to navigate to Press 5 and 6 to navigate to Auto Source Selec- Use the left and right cursor keys to select one 5.7 Reset menu 5.7.1 Factory Reset Use the up and down cursor keys to navigate to Press 5 and 6 to navigate to Factory Reset Use the left and right cursor keys to select one Use 3 and 4 to select one of the options Yes, No 5.8 Input Signal Selection Press 3 and 4 to navigate to the Press Enter to select Press 2 to select Use the down cursor keys to open the Use the left and right cursor keys to select Page 5.8.1 Input selection with the function key F1 6 Maintenance and servicing 6.1 Cleaning 7 Technical data 42" version (LCN-42, LCS-42) 7.1 General data 7.2 LCD panel 7.3 Electrical data 7.4 Operating conditions 7.5 CCFL (Cold Cathode Fluorescent Lamp) characteristics (ambient temperature (25 2)C) 7.6 Interfaces 7.6.1 Video IN (Composite Video) 7.6.2 S-Video 7.6.3 Component Video (mini DIN 8 pin) Page 7.6.4 SDI/HDSDI IN/OUT (BNC) (LCS-42 only) 7.6.5 DVI 7.6.6 RGB IN (D-Sub 15 pin) 7.6.7 RS232 IN 7.6.8 RS232 OUT 7.7 Factory settings Page 8 Technical data 47" version (LCN-47, LCS-47) 8.1 General data 8.2 LCD panel 8.3 Electrical data 8.4 Operating conditions 8.5 CCFL (Cold Cathode Fluorescent Lamp) characteristics (ambient temperature (25 2)C) 8.6 Interfaces 8.6.1 Video IN (Composite Video) 8.6.2 S-Video 8.6.3 Component Video Page 8.6.4 SDI/HDSDI IN/OUT (BNC) 8.6.5 DVI 8.6.6 RGB IN (D-Sub 15 pin) 8.6.7 RS232 IN 8.6.8 RS232 OUT 8.7 Factory setting 9. Compliant timing 9 Compliant timing 9.1 SDI input signals 9.2 HD-SDI input signals HD-SDI-Resolutions (M=1.001, p=progressive, i=interlaced) at data rate 1.485 or 1.485/1.001 Gb/s. Page 10 Troubleshooting 10.1 Faults 10.2 Contact Page 11 Compliance statement 11.1 FCC Compliance statement Page 12 Accessories 12.1 Required tools 12.2 Table stand 12.2.1 Scope of delivery 12.2.2 Installation Lay the monitor upside down on a clean(!) surface, bottom edge flush with e.g. edge of the table. When the screws are fastened tightly, put up the monitor Page 12.2.4 Height adjustment 12.3 Screen bracket (adapter plate) 12.3.1 Scope of delivery 12.3.2 Installation 12.4 Fixed wall mount 12.4.1 Scope of delivery 12.4.2 Installation Drill 4 holes, 10mm, to the wall in the given distances! Page 12.4.4 Wall pattern 12.5 Tiltable wall mount 12.5.1 Scope of delivery 12.5.2 Installation Drill 5 holes, 10mm, to the wall in the given distances! 12.5.3 Dimensions 12.5.4 Tilting 12.6 Short ceiling mount 12.6.1 Scope of delivery 12.6.2 Installation Page Page 12.6.3.2 Dimension of the 47" version: 12.6.4 Tilting 12.7 Long ceiling mount 12.7.1 Scope of delivery 12.7.2 Installation Page 12.7.3 Dimensions 12.7.3.1 Dimensions of the 42" version: 12.7.3.2 Dimension of the 47" version: 12.7.4 Tilting Page 13 Contact Barco Control Rooms GmbH BARCO N.V. BARCO N.V. Media