Manuals / Barco / Computer Equipment / Projector

Barco R9002328, R9002327 Produced by BARCO NV, April All rights reserved, Printed in Belgium

Models: R9002327 R9002328

1 55

Download 55 pages 18.13 Kb

Page 2

Image 2

Due to constant research, the information in this manual is subject to change without notice.

Produced by BARCO NV, April 1998.

Trademarks are the rights of their respective owners.

BARCO nv/Projection Systems

Noordlaan 5

8520 Kuurne

Belgium

Printed in Belgium

Page 2

Image 2

Barco R9002328 Produced by BARCO NV, April All rights reserved, Trademarks are the rights of their respective owners

Contents

R9002328 R9002327 INSTALLATIONMANUAL BARCO PROJECTION SYSTEMS VISIONBARCO nv/Projection Systems Noordlaan 8520 Kuurne Belgium Produced by BARCO NV, April All rights reservedTrademarks are the rights of their respective owners Printed in BelgiumRaster centering TABLE OF CONTENTSOptical lens focusing Alignment of the projectoron safety on installation on servicing on cleaning on re-packing WARNINGS SAFETY INSTRUCTIONSSAFETYINSTRUCTIONS on illuminationSAFETYINSTRUCTIONS Before operating your projector please read this manual thoroughlyand retain it for future reference SAFETYINSTRUCTIONS On safety SAFETYINSTRUCTIONSSAFETYINSTRUCTIONS On installationOn servicing On illumination On cleaningOn re-packing SAFETYINSTRUCTIONSSAFETYINSTRUCTIONS 5975069ABARCOVISION708200498 UNPACKING DIMENSIONSUNPACKING AND DIMENSIONS UNPACKING AND DIMENSIONS Unpacking UNPACKING AND DIMENSIONS Projector dimensionsUNPACKING AND DIMENSIONS 5975069ABARCOVISION708200498Where to install the projector? How to install the projector? INSTALLATION GUIDELINESINSTALLATION GUIDELINES Environment What about ambient light? Which screen type?INSTALLATION GUIDELINES EnvironmentWhat about ambient light ? Windows that face the screen should be covered by opaque drapery while the set is being viewed. It is desirable to install the projecting system in a room whose walls and floor are of non-reflecting material. The use of recessed ceiling lights and a method of dimming those lights to an acceptable level is also important. Too much ambient light results in a ‘wash out’ of the projected image. This appears as less contrast between the darkest and lightest parts of the image. With bigger screens, the ‘wash out’ becomes more important. As a general rule, darken the room to the point where there is just sufficient light to read or write comfortably. Spot lighting is desirable for illuminating small areas so that interference with the screen is minimalINSTALLATION GUIDELINES Which screen type? What image size? How big should the image be?B = Distance between ceiling and top of the screen INSTALLATION GUIDELINES Where to install the projector?Abbreviations used on drawing and diagrams on next pages CD = Total distance between projector and ceilingURQWYLHZ FHLOLQJSURMHFWRU 7RSYLHZBARCO projection table INSTALLATION GUIDELINES How to install the projector?BARCO ceiling support Access to controls Scan adaptation INSTALLATION SET UPINSTALLATION SET UP 5975069ABARCOVISION708200498INSTALLATION SET UP INSTALLATION SET UP Access to controlsOpening procedure Support the top cover with the hand, no support is incorporatedINSTALLATION SET UP REMOTE R GS B INSTALLATION SET UP Scan adaptationRS232 IN RS232 OUT S VIDEO S-VIDEOFRQQHFWRUV YUJHQFH+RULRQWDOVFDQ INSTALLATION SET UPbe plugged in with the contacts facing the tubes A Horizontal scan inversionB Vertical scan inversion INSTALLATION SET UPThe service mode menu will be dis- played INSTALLATION SET UPThe Projector set up menu will be displayed INSTALLATION SET UPPassword mode PROJECTOR SET UPPROJECTOR SET UP 5975069ABARCOVISION7082004989HUWLFDOVFDQ PROJECTOR SET UP Projector Set UpFRQQHFWRUV 5975069ABARCOVISION708200498PROJECTOR SET UP Password mode Socket for strap5975069ABARCOVISION708200498 POWER MAINS CONNECTIONPOWERCONNECTION refer replacement to qualified service personnel POWERCONNECTION Power mains cord connectionInput power mains voltage FusesPOWERCONNECTION Switching on/off Overview flow chart installation mode Scheimpfug adjustment INSTALLATION ADJUSTMENTSINSTALLATION ADJUSTMENTS Optical lens focusing Raster centeringRandom Access INSTALLATION ADJUSTMENTS Entering the adjustment modeInstallation ServiceInstallation INSTALLATION ADJUSTMENTS Overview flow chart installation modeAdjustment Mode Scheimpflug AdjustmentINSTALLATION ADJUSTMENTS Installation mode start up access menuTHE FOLLOWING INSTALLATION MENUS ARE RESERVED TO INSTALLATION ADJUSTMENTSRISK OF ELECTRICAL SHOCK NO USER ADJUSTABLE PARTS INSIDE AND TO BE PERFORMED ONLY BY BARCO PERSONNEL, ORINSTALLATION ADJUSTMENTS enter password Wrong passwordSelect with , , or then ENTER EXIT to return INSTALLATION ADJUSTMENTSCOMPOSE PASSWORD ???? 7 8 4 5 1 2 INSTALLATION ADJUSTMENTS Scheimpfug adjustment INSTALLATION ADJUSTMENTS HQVEROWV /HQVEROWV /HQVEROWV OXHOHQV *UHHQOHQV 5HGOHQVrange 2 in the middle 6FKHLPSIXJFRUUHFWLRQKDQGOH UDQJHUDQJH%OXHUDQJHUDQJHUDQJH*UHHQUDQJHUDQJHUDQJH5HGUDQJHHQWHU IRFXVLQJ INSTALLATION ADJUSTMENTS Optical lens focusingRUQHU IRFXVLQJ INSTALLATION ADJUSTMENTS Electrical focusing Electrical focus Red Green BlueINSTALLATION ADJUSTMENTS Raster centering forbidden area projected raster crt faceplate border phosphor borderINSTALLATION ADJUSTMENTS FRUUHFWUDVWHUZURQJSRVLWLRQUDVWHUSRVLWLRQCRT PROJECTION ANGLE ADJUSTMENT INSTALLATION ADJUSTMENTS CRT projection angle adjustmentCRT PROJECTION ANGLE ADJUSTMENT 7-145975069ABARCOVISION708200498 INSTALLATION ADJUSTMENTSThe same projection angle is misaligned for new 7-15Loosen the four hexagon screws C, C Move the red CRT towards the green CRT Pivot the red CRT until the center of theINSTALLATION ADJUSTMENTS Align crosshairs ENTER continue EXIT to returnINSTALLATION ADJUSTMENTS Alignment of the projector APPENDIX A CEILING MOUNT KIT CM50 Ceiling mount kit for 700 projectors CM50APPENDIX B G2 ADJUSTMENT G2 adjustment APPENDIX B G2 ADJUSTMENT Green G2 LED APPENDIX B G2 ADJUSTMENT