Manuals / Barco / Computer Equipment / Projector

Barco R9002327 INSTALLATION SET UP Access to controls, Opening procedure, Installation Set Up

Models: R9002327 R9002328

1 55

Download 55 pages 18.13 Kb

Page 21

Image 21

INSTALLATION SET UP

Access to controls

Opening procedure :

During the projector set up and installation it is necessary to open the top cover. To gain access, proceed as follow :

*Turn both lock screws with a screwdriver or a coin counter clockwise. * Lift up and pivot the top cover.

* Support the top cover with the hand, no support is incorporated.

INSTALLATION SET UP

4-2		5975069ABARCOVISION708200498

Page 21

Image 21

Barco R9002327, R9002328 installation manual INSTALLATION SET UP Access to controls, Opening procedure, Installation Set Up

Contents

BARCO PROJECTION SYSTEMS VISION R9002328 R9002327 INSTALLATIONMANUALTrademarks are the rights of their respective owners Produced by BARCO NV, April All rights reservedBARCO nv/Projection Systems Noordlaan 8520 Kuurne Belgium Printed in BelgiumOptical lens focusing TABLE OF CONTENTSRaster centering Alignment of the projectorSAFETYINSTRUCTIONS WARNINGS SAFETY INSTRUCTIONSon safety on installation on servicing on cleaning on re-packing on illuminationBefore operating your projector please read this manual thoroughly and retain it for future referenceSAFETYINSTRUCTIONS SAFETYINSTRUCTIONS SAFETYINSTRUCTIONS On safetyOn installation On servicingSAFETYINSTRUCTIONS On re-packing On cleaningOn illumination SAFETYINSTRUCTIONSSAFETYINSTRUCTIONS UNPACKING DIMENSIONS UNPACKING AND DIMENSIONS5975069ABARCOVISION708200498 UNPACKING AND DIMENSIONS Unpacking UNPACKING AND DIMENSIONS Projector dimensionsUNPACKING AND DIMENSIONS 5975069ABARCOVISION708200498INSTALLATION GUIDELINES INSTALLATION GUIDELINESWhere to install the projector? How to install the projector? Environment What about ambient light? Which screen type?What about ambient light ? EnvironmentINSTALLATION GUIDELINES Windows that face the screen should be covered by opaque drapery while the set is being viewed. It is desirable to install the projecting system in a room whose walls and floor are of non-reflecting material. The use of recessed ceiling lights and a method of dimming those lights to an acceptable level is also important. Too much ambient light results in a ‘wash out’ of the projected image. This appears as less contrast between the darkest and lightest parts of the image. With bigger screens, the ‘wash out’ becomes more important. As a general rule, darken the room to the point where there is just sufficient light to read or write comfortably. Spot lighting is desirable for illuminating small areas so that interference with the screen is minimalWhat image size? How big should the image be? INSTALLATION GUIDELINES Which screen type?Abbreviations used on drawing and diagrams on next pages INSTALLATION GUIDELINES Where to install the projector?B = Distance between ceiling and top of the screen CD = Total distance between projector and ceilingSURMHFWRU FHLOLQJURQWYLHZ 7RSYLHZINSTALLATION GUIDELINES How to install the projector? BARCO ceiling supportBARCO projection table INSTALLATION SET UP INSTALLATION SET UPAccess to controls Scan adaptation 5975069ABARCOVISION708200498Opening procedure INSTALLATION SET UP Access to controlsINSTALLATION SET UP Support the top cover with the hand, no support is incorporatedINSTALLATION SET UP RS232 IN RS232 OUT INSTALLATION SET UP Scan adaptationREMOTE R GS B S VIDEO S-VIDEO+RULRQWDOVFDQ YUJHQFHFRQQHFWRUV INSTALLATION SET UPB Vertical scan inversion A Horizontal scan inversionbe plugged in with the contacts facing the tubes INSTALLATION SET UPINSTALLATION SET UP The service mode menu will be dis- playedINSTALLATION SET UP The Projector set up menu will be displayedPROJECTOR SET UP PROJECTOR SET UPPassword mode 5975069ABARCOVISION708200498FRQQHFWRUV PROJECTOR SET UP Projector Set Up9HUWLFDOVFDQ 5975069ABARCOVISION708200498Socket for strap PROJECTOR SET UP Password modePOWER MAINS CONNECTION POWERCONNECTION5975069ABARCOVISION708200498 Input power mains voltage POWERCONNECTION Power mains cord connectionrefer replacement to qualified service personnel FusesPOWERCONNECTION Switching on/off INSTALLATION ADJUSTMENTS INSTALLATION ADJUSTMENTSOverview flow chart installation mode Scheimpfug adjustment Optical lens focusing Raster centeringInstallation INSTALLATION ADJUSTMENTS Entering the adjustment modeRandom Access ServiceAdjustment Mode INSTALLATION ADJUSTMENTS Overview flow chart installation modeInstallation Scheimpflug Adjustmentaccess menu INSTALLATION ADJUSTMENTS Installation mode start upRISK OF ELECTRICAL SHOCK NO USER ADJUSTABLE PARTS INSIDE INSTALLATION ADJUSTMENTSTHE FOLLOWING INSTALLATION MENUS ARE RESERVED TO AND TO BE PERFORMED ONLY BY BARCO PERSONNEL, ORenter password Wrong password INSTALLATION ADJUSTMENTSINSTALLATION ADJUSTMENTS COMPOSE PASSWORD ???? 7 8 4 5 1 2Select with , , or then ENTER EXIT to return INSTALLATION ADJUSTMENTS Scheimpfug adjustment range 2 in the middle 6FKHLPSIXJFRUUHFWLRQKDQGOH HQVEROWV /HQVEROWV /HQVEROWV OXHOHQV *UHHQOHQV 5HGOHQVINSTALLATION ADJUSTMENTS UDQJHUDQJH%OXHUDQJHUDQJHUDQJH*UHHQUDQJHUDQJHUDQJH5HGUDQJHINSTALLATION ADJUSTMENTS Optical lens focusing RUQHU IRFXVLQJHQWHU IRFXVLQJ Electrical focus Red Green Blue INSTALLATION ADJUSTMENTS Electrical focusingforbidden area projected raster crt faceplate border phosphor border INSTALLATION ADJUSTMENTS Raster centeringFRUUHFWUDVWHUZURQJSRVLWLRQUDVWHUSRVLWLRQ INSTALLATION ADJUSTMENTSCRT PROJECTION ANGLE ADJUSTMENT INSTALLATION ADJUSTMENTS CRT projection angle adjustmentCRT PROJECTION ANGLE ADJUSTMENT 7-14The same projection angle is misaligned for new INSTALLATION ADJUSTMENTS5975069ABARCOVISION708200498 7-15wards the green CRT Move the red CRT toLoosen the four hexagon screws C, C Pivot the red CRT until the center of theAlign crosshairs ENTER continue EXIT to return INSTALLATION ADJUSTMENTSINSTALLATION ADJUSTMENTS Alignment of the projector Ceiling mount kit for 700 projectors CM50 APPENDIX A CEILING MOUNT KIT CM50APPENDIX B G2 ADJUSTMENT G2 adjustment APPENDIX B G2 ADJUSTMENT APPENDIX B G2 ADJUSTMENT Green G2 LED