EUROGRAND EG2080-RW/BK

6.6.1 Key velocity

This parameter determines the volume of the sounds with reference to the key velocity applied, i.e. you can set here how hard you have to strike a key to achieve maximum volume.

The following section describes how to change the key velocity.

1)Press the VELOCITY button to select one of the following settings:

HARD: The keys must be played very hard to achieve maximum volume.

MEDIUM: The keys must be played with medium velocity to achieve maximum volume.

(default setting)

SOFT:

The keys must be played only lightly to achieve

 

maximum volume.

OFF:

If none of the LEDs lights up, each key stroke

 

will produce a defined volume, irrespective of

 

how hard you play the keys.

An LED above the button lights up to show the current setting. If all LEDs are out, key velocity is switched off. In this case you can adjust a fixed volume level as follows:

2)Press and hold the VELOCITY button, then use the -/NO and +/YES buttons to set the volume level to be produced when you play a key on the keyboard, irrespective of the key velocity applied.

+

The display reads:

1x127:Fixed volume level produced when you play a key on the keyboard (default setting: 64)

3)Keep the VELOCITY button pressed, then press the -/NO and +/YES buttons simultaneously to recall the standard setting.

The key velocity setting has no effect on the following sounds: HARPSICHORD, CEMBALO, JAZZ ORGAN, CHURCH ORGAN and PIPE ORGAN.

TIP: young pianists might find it easier to use a SOFT key velocity setting.

6.6.2 Soft pedal intensity

Use this function to adjust the intensity of the soft pedal effect.

Please enter EDIT mode (see chapter 6.1) and select the following function.

Function:E4.2

Value:1x5

Description:

3: Normal soft pedal intensity (default setting)

1: Low soft pedal intensity

5: High soft pedal intensity

The function will be effective only if the left pedal is used as a soft pedal, but NOT to start/stop the music sequencer (see chapter 6.5.8).

6.6.3 Fine tuning

The EG2080 can be detuned slightly to adapt it to other instruments or tunings. The setting made here affects the pitch of all keys.

The following section describes how to adjust the fine tuning of the EG2080. The tuning shown in the display is referenced to the concert pitch „A“ in Hertz (Hz).

Please enter EDIT mode (see chapter 6.1) and select the following function.

Function:E1

Value:427x453

Description:

440: Western European equal tuning (default setting)

453: Maximum detuning upwards

427: Maximum detuning downwards

1/5-Hz steps are shown as follows (figures separated by one or two dots):

440: 440 Hz

4.40: 440,2 Hz

44.0: 440,4 Hz

440.: 440,6 Hz

4.40.: 440,8 Hz

6.6.4 Tunings

The EG2080 provides different tunings developed during the past few centuries. The tuning used most often today is called equal tuning and has been a characteristic element of the music composed from the 19th century up to the present. However, for some baroque pieces (e.g. by J. S. Bach) it can be interesting to use an older tuning system.

In the history of music, the development of the individual tunings can be traced back to the development of scales and polyphony and the resulting adaptation of instruments and their tuning. Apart from these historical reasons the limited tuning aids available in former times played an important role for the practical implementation of tunings.

The EG2080 provides the following tunings:

Equal tuning (default setting)

Equal tuning divides one octave into twelve intervals of equal size or spacing. Thus, each half-tone is detuned slightly to the same extent, with the octave being the only perfect interval. This has been the most common tuning since the 19th century, as it makes it possible to play all twelve major/minor keys.

Pure major/minor intonation

This tuning is based on the perfect tuning of the seven notes of one scale (e.g. C major). Triads played one fifth above or below are also perfect, since they use the notes of the basic key. However, all other keys are not playable, since their frequency relationships change depending on the basic note.

20

6. ADVANCED OPERATION