Overview, Product Features | Belkin F5D7001 specs

Overview

Product Features

The Card complies with the IEEE 802.11g standard in order to communicate with other 802.11g-compliant wireless devices at 54Mbps or the faster 125 High-Speed Mode (HSM). The Card is compatible with all 802.11g devices as well as other 802.11b products at 11Mbps. 802.11g products run at speeds of up to 54Mbps (or 125Mbps* using HSM) and operate on the same 2.4GHz frequency band as 802.11b Wi-Fi products.

•2.4GHz ISM (Industrial, Science, and Medical) band operation

•Integrated easy-to-use Wireless Configuration Utility

•PCI interface, for operation in virtually any desktop computer

•WPA, 64-bit WEP (Wired Equivalent Privacy), or 128-bit encryption

•Wireless access to networked resources

•Support for both Infrastructure and Ad-Hoc (peer-to-peer) networking modes

•Data rate of up 125Mbps* in High-Speed Mode (802.11g 125HSM), 54Mbps (802.11g), or 11Mbps (802.11b)

•Easy installation and use

•External antenna

•LED power and network link indicators

*When operating in High-Speed Mode, this Wi-Fi device may achieve an actual throughput of up to or greater than 34.1 Mbps, which is the equivalent throughput of a system following 802.11g protocol and operating at a signaling rate of 125 Mbps. Actual throughput will vary depending on environmental, operational and other factors.

6

Image 8

Belkin F5D7001 user manual Overview, Product Features

Contents

High-Speed Mode Wireless G Desktop Network Card Table of Contents Introduction Introduction Cordless Phone Placement Avoid Obstacles and Interference Choose the quietest channel for your wireless network Secure connections, VPNs, and AOL Introduction Product Features Overview Connection rates of up to 54Mbps or 125Mbps* using HSM Difficult-to-wire environmentsCompatibility with 802.11b products Frequently changing environments Card Connector Detachable Antenna Product SpecificationsActivity LED green Link LED orange Package Contents System Requirements Installing and Setting Up the Card Install the Software Insert the Card into the Computer Installing and Setting Up the Card Let Windows Finish the Installation Installing and Setting Up the Card Installation is now complete Available Networks Setting Wireless Network PreferencesClick on the Wireless Networks tab Enable Radio Preferred Networks Add, RemoveSystem Tray Icon Properties Computer-to-Computer Ad-Hoc Networks Only Any Available Network Access Point PreferredAccess Point Infrastructure Networks Only Securing your Wi-FiNetwork Encryption Keys WEP Wired Equivalent PrivacyBit WEP WPA Wi-Fi Protected Access C3030FAF0F4BB2C3D44BC3D4E7 = 128-bit WEP key Using a Hexadecimal Key Changing the Wireless Security Settings WEP Setup Bit WEP Encryption C3030FAF0F4BB2C3D44BC3D4E7 = 128-bit WEP key WPA-PSK no server WPA with server Settings Using the Belkin Wireless LAN Utility Type your WEP key in the Network key box Using the Belkin Wireless LAN Utility Using the Belkin Wireless LAN Utility Monitoring the Status of your Network Connection Signal Client IP AddressNetwork Connection Type Radio State Monitoring Data Transfer Click on the Statistics tab Finding Available Networks in your Area Performing Diagnostic Tests on your Connection Click on the Diagnostics tabControl Registers Sprom Format Version LED Test Interrupt TestLoopback Test Troubleshooting Can’t connect to the Internet wirelessly Name of your wireless network appears in Available Networks Installation CD-ROM does not start Setup Utility Power LED does not come on Card is not working Link LED is solid but cannot connect to the Internet Signal strength is poor Data transfer is sometimes slow Troubleshooting Wireless PCI Card is not Detected by Operating System Wireless Comparison What’s the difference between 802.11b, 802.11g and 802.11a? Technical Support Europe 00 800 223 55 Australia 1800 666 FCC Statement Federal Communications Commission Notice Information Belkin Corporation Limited Lifetime Product Warranty Belkin Tech Support