Belkin LH 4, LH R Cover 1, Cover 2

Chapter 3 Removing and Replacing Covers

bottom front of the chassis. To remove, pull the bezel forward until it unsnaps,

then lift the bezel forward and upward from the chassis face (see Figure 3-1).

Figure 3-1. Removing the HP NetServer LH 4 Bezel

CAUTION The NetServer covers are heavy. Support them as you remove

them, and allow room to move them away from the NetServer

and for storage when removed.

Cover 1

Once you have rem ove d the bezel, r e m ove cover 1 by unscrewi n g the thum bscrew

and then pulling the cover forward to disengage it. Lift it outward and away from

the chassis (see Figure 3-2).

Cover 2

Remove cover 2 by unscrewing the thumbscrew, pulling the cover forward and

then slightly sideways to disengage it. Lift it up and away from the chassis (see

Figure 3-2).

Contents

Main Notice Audience Assumptions Contents Page Page Page 1 Introduction Verifying Contents HP NetServer LH 4 Installation Procedures HP NetServer LH 4r Installation Procedur es HP NetServer LH 4 to LH 4r Conversion Kit 2 Controls, Ports, and Indicators Front Panel RESET Page Rear Panel Controls, Ports, and Indicators Connecting the NetServer to AC Power Power-On Tests 3 Removing and Replacing Covers Removing the HP NetServer LH 4 Covers Bezel Cover 1 Cover 2 Cover 3 Replacing the HP NetServer LH 4 Covers Removing the HP NetServer LH 4r Covers Bezel Page Page Replacing the HP NetServer LH 4r Covers Page 4 Accessory Boards The I/O Board By default, SCSI channel A is connected to the hot-swap mass By default, the integrated HP NetRAID subsystem is enabled for By default, SCSI channel B is connected to the non-hot-swap By default, the integrated HP NetRAID subsystem is disabled for If you enable HP NetRAID for SCSI B, all non-hot-swap SCSI Installing Accessory Boards Page Page Page 5 Installing Additional Memory Installing Additional Memory in the LH 4 Page Installing Additional Memory in the LH 4r Page Page Page Page 6 Installing Mass Storage Devices Supported Mass Storage Devices SCSI Addressing Hot-Swap Mass Storage Page Page Page Installing a Hot-Swap Hard Disk Drive Page Page Page Page Removing a Hot-Swap Hard Disk Drive Integrated HP NetRAID 7 Installing Additional Power Supplies Installing an Additional Power Supply Ventilating Fans 8 Installing the NetServer in an HP Rack System/E or Rack System/U Preparing for Installation Prevent Rack Tip-Over, Equipment Damage and In jur y Tools Required Installing the Slides Marking the Columns Installing Rack Nuts Installing Bar Nuts Attaching the Slides Page Page Installing the NetServer Page Page Securing the NetServer to the Rack Page Page Page Page Page 10 Configuring the NetServer Contents of the NetServer Navigator CD-ROM Obtaining NetServer Product History Readme File Viewing the Readme File Configuration Assistant and Installation Assistant If you need to verify or modify SCSI host adapter settings, or if you need If you need to change the system defaults for enabling/disabling the Run Configuration Assistant and Installation Assistan t Express Configuration Configure Mass Storage: The HP NetServer is shipped with the hot-swap Custom Configuration Page Page Replicate Configuration HP Management Solutions TopTools for Servers Integrated Remote Assistant PcANYWHERE-32 NetServer Utilities User Preferences Setup Utility Integrated HP NetRAID [Enable/Disable] Include SCSI_A Channel [Yes/No] Include SCSI_B Channel [Yes/No] Symbios Configuration Utility ISA Non-Plug-and-Play Boards (Optional) Reserving Resources for ISA Non-Plu g-and-Play Boards Configuring an ISA Non-Plug- and-Play Board Page Page 11 HP Information Assistant Using Information Assistant Getting Help Finding Information Copying and Printing Infor mati on Installing HP Information Assistant Software Installing from the CD-ROM Page 12 Troubleshooting Troubleshooting Tools DiagTools Common Installation Problems Troubleshooting Sequence First make sure that the system is configured properly. Most system If the System Does Not Power On If the System Powers On, but Fails POST (Power-On Self Test) If the System Passes POST (Power-On Self Test) but Does Not Function Error Messages POST Error Codes Page Appendix A Installing the NetServer in an HP Systems Rack Preparing for Installation Rack Templa te Tools Required Installing the Slides Marking the Columns Page Page Installing Bar Nuts Attaching the Slides Page Page Page Appendix B Specifications Environment Weight and Dimensions Appendix C Regulatory Information Notice for USA FCC Radio Frequency Emissions Statements CD-ROM Notice for Canada: DOC Requirements Battery Appendix C Regulatory Information Notice for Finland: Laser Safety Statement Notice for Germany Noise Declaration and Ergonomics Laser Safety Statement Notice for Japan For Products Labeled as Class B For Products Labeled as Class A Power Line Harmonics Notice for Korea: RFI Statement Notice for Taiwan: Class A Warning Statement Mexico: Hardware Warranty Statement Pliza de Gara n ta CONDICIONES Notas Notice for U.K.: General Approval Appendix D Warranty and Software License Warranty HP Software Product License Agreement Page Page Page Index