Manuals / BenQ / Computer Equipment / Projector

BenQ MP525 ST user manual

Models: MP525 ST

1 66

Page 45

Main menu	Sub-menu		Options
5.		Closed Caption	On/Off
SYSTEM	Closed Caption Enable
SYSTEM		Caption Version	CC1/CC2/CC3/CC4
SETUP:		Caption Version	CC1/CC2/CC3/CC4
SETUP:
Advanced	Reset All Settings
	FAQ-Image and Installation
	FAQ-Features and Service
6.			•	Source
INFORMA-			•	Picture Mode
TION	Current System Status		•	Resolution
TION	Current System Status		•	Color System
			•	Color System
			•	Equivalent Lamp Hour
			•	Firmware Version

Note that the menu items are available when the projector detects at least one valid signal. If there is no equipment connected to the projector or no signal detected, limited menu items are accessible.

The default values listed in this manual, especially on pages 46-50, are for reference only. They may vary between the projectors due to the continuous improvement to the products.

Operation 45

Page 45

Image 45

Contents

Welcome MP515 ST/MP525 ST Digital Projector User ManualImportant safety Table of contentsPositioning your Warranty and CopyrightImportant safety instructions Safety Instructions3. Refer servicing to qualified service personnel 4 Important safety instructions Safety Instructions Continued14. Do not block the ventilation holes installation Introduction Projector featuresShipping contents Standard accessoriesOptional accessories Projector exterior view Projector Controls and functions5. II Power 9. LAMP indicator light13. Mode/Enter 14. SOURCECeiling mounting the projector 1. II Power Remote control6. Volume + 2. FreezeReplacing the remote control battery Remote control effective range13. Timer On 14. Timer Set upChoosing a location Positioning your projector1. Front Table 2. Front CeilingObtaining a preferred projected image size 16 Positioning your projector How to determine the recommended screen size for a given distanceProjection dimensions Maximum zoomScreen Center of lens Projection distance Connection VGA to DVI-A cableAudio L/R cable Connecting a computer Connecting a computer or monitorConnecting a monitor MP525 ST only To connect the projector to a notebook or desktop computerConnecting audio Connecting Video source devicesConnecting an HDMI device MP515 ST only Connecting a Component Video source deviceTo connect the projector to an HDMI device To connect the projector to a Component Video source deviceTo connect the projector to an S-Video/Video source device Connecting an S-Video/composite Video source deviceStarting up the projector OperationAdjusting the projected image Adjusting the projection angleAuto-adjusting the image Correcting keystone Fine-tuning the image size and clarityUsing the remote control Using the OSD menuCurrent input signal Using the menusSYSTEM SETUP Basic SYSTEM SETUP BasicUtilizing the password function Using a security cable lockSecuring the projector Setting a passwordEntering the password recall procedure If you forget the passwordChanging the password 2. Press Mode/Enter. The message INPUT CURRENT PASSWORD displaysDisabling the password function Changing Color Space MP515 ST only Switching input signalSelecting the aspect ratio Magnifying and searching for detailsUsing the remote control Using the OSD menu32 Operation About the aspect ratioUsing Wall Color Optimizing the imageSelecting a picture mode Setting the User 1/User 2 mode Fine-tuning the image quality in user modesAdjusting Brightness Adjusting ContrastAdjusting Tint Adjusting ColorAdjusting Sharpness Adjusting Brilliant ColorTo adjust the settings To cancel the timer, perform the following steps Setting the presentation timerHiding the image Using the OSD menuHow to use the Timer On key? Utilizing FAQ function Freezing the image3. Press Mode/Enter Operating in a high altitude environment Locking control keysTo activate the High Altitude Mode Personalizing the projector menu display Adjusting the soundAdjusting the sound level Turning off the Power On/Off Ring ToneShutting down the projector Menu system Menu operationPower On/Off Ring Disable/30 min/1 hr/2 hr/3 hr/4 hr/8Reset Lamp Timer Security SettingsNote that the menu items are available when the projector detects at least one valid signal. If there is no equipment connected to the projector or no signal detected, limited menu items are accessible Description of each menu Saves the settings made for User 1 or User 2 mode See Adjusting Brilliant Color on page 35 for detailsSee Switching input signal on page 30 for details See 3D Color Management on page 35 for detailsMenu Display Time 15 sec Menu Position CenterSee Hiding the image on page 38 for details See Adjusting the sound on page 41 for details Mute Off VolumeSee Setting Lamp Mode as Economic on page 52 for details Reset Lamp TimerReturns all settings to the factory preset values Cleaning the lens MaintenanceCleaning the projector case Care of the projectorGetting to know the lamp hour Lamp informationExtending lamp life Setting Lamp Mode as Economicthe inconvenience when the projector runs out of Timing of replacing the lampperformance. If the projector is normally run with 2950 hours. A new lamp should be fitted to avoidReplacing the lamp 3. Turn the projector over. Then loosen the screws on the lamp cover4. Remove the lamp cover from the projector 5. Loosen the screw that secures the lamp. Be careful not to lose the screw as it is needed to hold the lamp in place. It is strongly recommended that you use a magnetic-head screwdriver Resetting the lamp timer Power events IndicatorsLight Status & DescriptionRemote control does not work TroubleshootingThe password is incorrect The projector does not turn onOptical SpecificationsElectrical MechanicalDimensions Ceiling mount installation255 mm W x 114 mm H x 236 mm D Timing chart Supported timing for PC input-MP515 ST/MP525 STUXGA Supported timing for HDMI HDCP input-MP515 ST 62 SpecificationsUXGA HDCPSupported timing for Component-YPbPr input-MP515 ST/ MP525 ST Signal FormatSupported timing for Video and S-Video inputs-MP515 ST/ MP525 ST Vertical Frequency HzLimited warranty Warranty and Copyright informationCopyright DisclaimerFCC statement Regulation statementsEEC statement WEEE directive66 Regulation statements Accessibility Requirements for Rehabilitation Act of 1973, Section