Manuals / BenQ / Computer Equipment / Projector

BenQ MP625P user manual Connecting a Component Video source device

Models: MP625P

1 68

Download 68 pages 14.66 Kb

Page 22

Connecting a Component Video source device

Examine your Video source device to determine if it has a set of unused Component Video output jacks available:

•If so, you can continue with this procedure.

•If not, you will need to reassess which method you can use to connect to the device.

To connect the projector to a Component Video source device:

1.Take a Component Video to VGA (D-Sub) adaptor cable and connect the end with 3 RCA type connectors to the Component Video output jacks of the Video source device. Match the color of the plugs to the color of the jacks; green to green, blue to blue, and red to red.

2.Connect the other end of the Component Video to VGA (D-Sub) adaptor cable (with a D-Sub type connector) to the COMPUTER 1 or COMPUTER 2 jack on the projector.

3.If you wish to make use of the projector (mixed mono) speaker(s) in your presentations, take a suitable audio cable and connect one end of the cable to the audio output jack of the device, and the other end to the AUDIO jack of the projector.

4.If you wish, you can use another suitable audio cable and connect one end of the cable to the AUDIO OUT jack of the projector, and the other end to your external speakers (not supplied).

Once connected, the audio can be controlled by the projector On-Screen Display (OSD) menus. See "Audio Settings" on page 50 for details.

The built-in speaker will be muted when the AUDIO OUT jack is connected.

•The projector is only capable of playing mixed mono audio, even if a stereo audio input is connected. See "Connecting audio" on page 20 for details.

•If the selected video image is not displayed after the projector is turned on and the correct video source has been selected, check that the Video source device is turned on and operating correctly. Also check that the signal cables have been connected correctly.

22 Connection

Image 22

BenQ MP625P Connecting a Component Video source device, To connect the projector to a Component Video source device

Contents

MP615P/MP625P Digital Projector User Manual WelcomePositioning your Table of contentsImportant safety Warranty and Copyright3. Refer servicing to qualified service personnel Important safety instructionsSafety Instructions operate your projector. Save it forSafety Instructions Continued 4 Important safety instructionsSafety Instructions Continued 13. Do not place this projector in any of the following environmentsSafety Instructions Continued 6 Important safety instructionsProjector features IntroductionStandard accessories Shipping contentsOptional accessories Front/upper side Projector exterior viewSee Projector on page 10 for 1. Focus ring Controls and functions Projector3. LAMP indicator light 2. Zoom ringCeiling mounting the projector 6. Volume + Remote control1. II Power See Using the menus on page 27 for details15. Timer Setup Replacing the remote control battery14. Timer On See Setting the presentation timer onSet Front Ceiling in the SYSTEM SETUP Basic Positioning your projectorChoosing a location Set Rear Table in the SYSTEM SETUP Basic ProjectorObtaining a preferred projected image size Positioning your projectorHow to determine the recommended screen size for a given distance Diagonal Projection dimensionsScreen size Max lengthConnection 18 ConnectionConnecting a monitor Connecting a computer or monitorConnecting a computer To connect the projector to a notebook or desktop computername Connecting Video source devicesConnecting audio HDMIConnecting an HDMI source device MP625P only To connect the projector to an HDMI source deviceConnecting a Component Video source device To connect the projector to a Component Video source deviceConnecting an S-Video/composite source device To connect the projector to an S-Video/Video source deviceOperation Starting up the projectorAuto-adjusting the image Adjusting the projected imageAdjusting the projection angle horizontal angleFine-tuning the image size and clarity Correcting keystoneUsing the menus 2. Use / to highlight the SYSTEM SETUP Basic menuSetting a password Using a security cable lockUtilizing the password function If you forget the passwordDisabling the password function Entering the password recall procedureChanging the password 2. Press Mode/Enter. The message INPUT CURRENT PASSWORD displays30 Operation Switching input signal Changing Color Space MP625P onlySelecting the aspect ratio Magnifying and searching for detailsAbout the aspect ratio Auto Scales an image proportionally to fit the Setting the User 1/User 2 mode Optimizing the imageSelecting a picture mode 2. Go to the PICTURE Picture Mode menuAdjusting Brightness Using Wall ColorFine-tuning the image quality in user modes Adjusting Contrast3D Color Management About color temperatures2. Press Mode/Enter and the 3D Color Management page displays 7. Repeat steps 3 to 6 for other color adjustments Presentation Timer page Setting the presentation timerTo cancel the timer, perform the following steps Increases from 0 to the preset timeHiding the image Remote paging operationsHow to use the Timer On key? Utilizing FAQ function Freezing the imageOperating in a high altitude environment Adjusting the soundAdjusting the sound level Muting the soundPersonalizing the projector menu display Shutting down the projectorMain menu Menu operationMenu system Sub-menu4. SYSTEM SETUP Basic 44 OperationChange password SETUPReset lamp timer Direct power ondefault setting Description of each menuDESCRIPTION default setting/value not white. See Using Wall Color on page 35 for detailsSee Adjusting Contrast on page 35 for details DESCRIPTION default setting/valuedefault setting FUNCTIONSee Switching input signal on page 31 for details See Adjusting Brilliant Color on page 35 for detailsSee Selecting a Color Temperature on page 35 for details See 3D Color Management on page 36 for detailsTimer position Timer periodTimer display Timer counting directionPower on lock Reset lamp timerChange password MuteFUNCTION Closed Caption Enabledefault setting/ DESCRIPTION default setting/value Caption Version6. INFORMATION menu Cleaning the projector case MaintenanceCleaning the lens Care of the projectorExtending lamp life Lamp informationGetting to know the lamp hour Setting Lamp mode as EconomicStatus Timing of replacing the lampSee Setting Lamp mode as Economic on page MessageReplacing the lamp 2. Loosen the screw on the lamp coverprojector and b lifting it off Resetting the lamp timer Power events IndicatorsPOWER LightThe password is incorrect TroubleshootingRemote control does not work The projector does not turn onElectrical SpecificationsOptical ControlCeiling mount screws DimensionsCeiling mount installation Unit mmTiming chart Supported timing for PC input64 Specifications Supported timing for HDMI inputSupported timing for Video and S-Video inputs Supported timing for Component-YPbPr inputColor sub-carrier Copyright Warranty and Copyright informationLimited warranty DisclaimerEEC statement Regulation statementsFCC statement WEEE directiveAccessibility Requirements for Rehabilitation Act of 1973, Section 68 Regulation statements