System Setup Advanced menu Function Description | BenQ MX501-V

5. SYSTEM SETUP: Advanced menu

	Function	Description
		Selects a baud rate that is identical with your computer’s so that you can
	Baud Rate	connect the projector using a suitable RS-232 cable and update or
	Baud Rate	download the projector’s firmware. This function is intended for

		qualified service personnel.

	Test Pattern	Selecting On enables the function and the projector displays the grid test
	Test Pattern	pattern. It helps you adjust the image size and focus and check that the
		projected image is free from distortion.

		Closed Caption Enable
		Activates the function by selecting On when the selected input signal
		carries closed captions.
	Closed	• Captions: An on-screen display of the dialogue, narration, and
	Closed	sound effects of TV programs and videos that are closed captioned
	Caption	(usually marked as "CC" in TV listings).
		Caption Version
		Selects a preferred closed captioning mode. To view captions, select
		CC1, CC2, CC3, or CC4 (CC1 displays captions in the primary language
		in your area).

		Monitor Out
		Selecting On enables the function. The projector can output a VGA
		signal when it is in standby mode and the COMPUTER 1 jack is
		correctly connected to devices. See "Connection" on page 15 for how to
		make the connection.
	Standby	Audio Pass Through
	Settings	Selecting On enables the function. The projector can play sounds when
	Settings	it is in standby mode. Connect the correct signal cable and connect the

		audio cable to the AUDIO IN jack. See "Connection" on page 15 for how
		to make the connection.
		Enabling this function slightly increases the standby power
		consumption.

	Reset All	Returns all settings to the factory preset values.
	Reset All	The following settings will still remain: Phase, H. Size, User 1, User
	Settings
	Settings	2, Language, Projector Position, High Altitude Mode, Security
		Settings and Baud Rate.

42 Operation

Image 42

BenQ MX501-V System Setup Advanced menu Function Description, Baud Rate, Test Pattern, Closed, Caption, Standby, Reset All

Contents

Welcome MX501/MS500/MX501-V/MS500-V Digital Projector Table of contents Refer servicing to qualified service personnel Important safety instructionsSafety Instructions Important safety instructions Safety Instructions Locations where the altitudes are higher Locations near fire alarmsLocations with an ambient temperature Confined. Allow at least 50 cm clearance Serviced InstalledIt from the power supplys power outlet Do not step on the projector or place Projector features IntroductionIntroduction Shipping contents Projector exterior view Controls and functions Projector Remote control Pull out the battery holder Remote control effective rangeReplacing the remote control battery Operating the projector from the front Front Table Positioning your projectorChoosing a location Front Ceiling Projection dimensions Obtaining a preferred projected image size Connection Connection Terminal name Terminal appearance Connecting video source devicesConnecting audio Component Video Better Good Normal Operation Starting up the projectorOperation Auto-adjusting the image Adjusting the projected imageAdjusting the projection angle Fine-tuning the image size and clarity Correcting keystone Use / to highlight the System Setup Basic menu Using the menusFollowing example describes how to set the OSD language Below is the overview of the OSD menu Setting a password Using a security cable lockUtilizing the password function Highlight Change Security Settings and press MODE/ENTER If you forget the password Entering the password recall procedureWrite down the number and turn off your projector Disabling the password function Switching input signalChanging the password Enter a new password Magnifying and searching for details Selecting the aspect ratioTo select the source About the aspect ratio Projectors native resolution in its Displayed in the centerAdjustments Screen with a 169 aspect ratio Operation Setting the User 1/User 2 mode Using Wall ColorSelecting a picture mode Go to the Picture Picture Mode menu Fine-tuning the image quality in user modes 3D Color Management Press To highlight Saturation and adjust itsEvery adjustment made will reflect to Range at 0, only pure red in the projected Count Up Increases from 0 to the preset time Count Down Setting the presentation timerTo cancel the timer, perform the following steps Selection Description Hiding the image Remote paging operationsFreezing the image Locking control keys To activate the High Altitude Mode Operating in a high altitude environmentCreating your own startup screen only for MX501/ MX501-V Turning off the Power On/Off Ring Tone Adjusting the soundAdjusting the sound level Shutting down the projector Direct power off Once the cooling process finishes, a Power Off Ring Main menu Sub-menu Options Menu operationMenu system Basic Main menu Sub-menu Options System Setup Basic Advanced Description of each menu Save Settings Picture ModeTemperature Display menu Picture menu Function Description Teaching Settings System Setup Basic menu Function Description Quick AutoTimer Search Background Panel KeyLock Splash Baud Rate System Setup Advanced menu Function DescriptionReset All Test Pattern Current SystemStatus Maintenance Care of the projector Lamp information Setting Lamp Mode as EconomicSetting Auto Power Off Getting to know the lamp hour Timing of replacing the lamp Status Message Replacing the lamp Use the handle to slowly pull the lamp out Projector Connect the power and restart the projector Resetting the lamp timerTime will be reset to Lamp events IndicatorsLight Status & Description Power events Thermal events Troubleshooting Specifications Projector specifications Dimensions Ceiling mount installation Timing chart Supported timing for PC input Timing Supported timing for Component-YPbPrinputSupported timing for Video and S-Video inputs Vertical Horizontal Copyright Warranty and Copyright informationLimited warranty Disclaimer