Panel Key, Lock, Background, Splash, MyScreen | BenQ MX501 instruction

		Function
		Panel Key
	4.	Panel Key
	SYSTEM	Lock
	SYSTEM	Background
		Background
	SETUP:	Color
	SETUP:	Splash
		Splash
	Basic	Screen
	Basic	MyScreen
	menu	(only for
	menu	MX501/
		MX501-V)
		High
		Altitude
	5.	Mode
	5.
	SYSTEM	Audio
		Audio
		Settings
	SETUP:	Lamp
		Lamp
	Advanced	Settings
	Advanced
	menu	Security
		Security
		Settings

Description

Disables or enables all panel key functions except POWER on the projector and keys on the remote control. See "Locking control keys" on page 31 for details.

Sets the background color for the projector.

Allows you to select which logo screen will display during projector start-up. The following options are available: BenQ logo, My Screen, Black screen, Blue screen.

Captures and stores the projected picture as My Screen. See "Creating your own startup screen (only for MX501/MX501-V)" on page 32 for details.

In the unlikely event that the capturing action fails, change your target picture.

A mode for operation in high altitude areas. See "Operating in a high altitude environment" on page 32 for details.

Mute

Volume

Power On/Off Ring Tone

See "Adjusting the sound" on page 33 for details.

Lamp Mode

See "Setting Lamp Mode as Economic" on page 45 for details.

Reset lamp timer

See "Resetting the lamp timer" on page 49 for details.

Equivalent Lamp Hour

See "Getting to know the lamp hour" on page 45 for details on how the total lamp hour is calculated.

Change Password

You will be asked to enter the current password before changing to a new one. See "Utilizing the password function" on page 21 for details.

Change Security Settings

Power On Lock

Splash Screen Lock

See "Utilizing the password function" on page 21 for details.

Operation 41

Image 41

BenQ MX501-V, MS500-V Panel Key, Lock, Background, Splash, MyScreen, High, Altitude, Audio, Lamp, Security

Contents

MX501/MS500/MX501-V/MS500-V Digital Projector Welcome Table of contents Safety Instructions Important safety instructionsRefer servicing to qualified service personnel Important safety instructions Safety Instructions Locations with an ambient temperature Locations near fire alarmsLocations where the altitudes are higher Confined. Allow at least 50 cm clearance It from the power supplys power outlet InstalledServiced Do not step on the projector or place Introduction Projector featuresIntroduction Shipping contents Projector exterior view Projector Controls and functions Remote control Replacing the remote control battery Remote control effective rangePull out the battery holder Operating the projector from the front Choosing a location Positioning your projectorFront Table Front Ceiling Obtaining a preferred projected image size Projection dimensions Connection Connection Connecting audio Connecting video source devicesTerminal name Terminal appearance Component Video Better Good Normal Operation OperationStarting up the projector Adjusting the projection angle Adjusting the projected imageAuto-adjusting the image Fine-tuning the image size and clarity Correcting keystone Following example describes how to set the OSD language Using the menusUse / to highlight the System Setup Basic menu Below is the overview of the OSD menu Utilizing the password function Using a security cable lockSetting a password Highlight Change Security Settings and press MODE/ENTER Write down the number and turn off your projector If you forget the passwordEntering the password recall procedure Changing the password Switching input signalDisabling the password function Enter a new password To select the source Magnifying and searching for detailsSelecting the aspect ratio Adjustments Projectors native resolution in its Displayed in the centerAbout the aspect ratio Screen with a 169 aspect ratio Operation Selecting a picture mode Using Wall ColorSetting the User 1/User 2 mode Go to the Picture Picture Mode menu Fine-tuning the image quality in user modes Every adjustment made will reflect to Press To highlight Saturation and adjust its3D Color Management Range at 0, only pure red in the projected To cancel the timer, perform the following steps Setting the presentation timerCount Up Increases from 0 to the preset time Count Down Selection Description Freezing the image Remote paging operationsHiding the image Locking control keys Creating your own startup screen only for MX501/ MX501-V To activate the High Altitude ModeOperating in a high altitude environment Adjusting the sound level Adjusting the soundTurning off the Power On/Off Ring Tone Shutting down the projector Once the cooling process finishes, a Power Off Ring Direct power off Menu system Menu operationMain menu Sub-menu Options Basic Main menu Sub-menu Options System Setup Basic Advanced Description of each menu Temperature Picture ModeSave Settings Display menu Picture menu Function Description Teaching Timer System Setup Basic menu Function Description Quick AutoSettings Search Lock Panel KeyBackground Splash Reset All System Setup Advanced menu Function DescriptionBaud Rate Test Pattern Status CurrentSystem Care of the projector Maintenance Setting Auto Power Off Setting Lamp Mode as EconomicLamp information Getting to know the lamp hour Status Message Timing of replacing the lamp Replacing the lamp Use the handle to slowly pull the lamp out Projector Time will be reset to Connect the power and restart the projectorResetting the lamp timer Light Status & Description Power events IndicatorsLamp events Thermal events Troubleshooting Projector specifications Specifications Ceiling mount installation Dimensions Supported timing for PC input Timing chart Supported timing for Video and S-Video inputs Supported timing for Component-YPbPrinputTiming Vertical Horizontal Limited warranty Warranty and Copyright informationCopyright Disclaimer