Controls and functions, Projector | BenQ MX501-V, MS500-V manual

Controls and functions

Projector

1

28 9

3

8.	TEMPerature warning light
	Lights up red if the projector's
	temperature becomes too high.
9.	POWER indicator light
	Lights up or flashes when the projector is
	under operation.
10.	AUTO

4

5

6

7

1.Focus ring

10 11 12

13

14 11

Automatically determines the best picture
timings for the displayed image.
11. Keystone/Arrow keys ( / Up,	/
Down)
Manually corrects distorted images
resulting from an angled projection.

Adjusts the focus of the projected image.

2.Zoom ring

Adjusts the size of the image.

3.LAMP indicator light

Indicates the status of the lamp. Lights up or flashes when the lamp has developed a problem.

4.MENU/EXIT

Turns on the On-Screen Display (OSD) menu. Goes back to previous OSD menu, exits and saves menu settings.

5. Left/

Decreases the projector volume.

6.MODE/ENTER

Selects an available picture setup mode.

Activates the selected On-Screen Display (OSD) menu item.

7.BLANK

Used to hide the screen picture.

12.		POWER


	Toggles the projector between standby
	mode and on.
13.		Right/

Increases the projector volume.

When the On-Screen Display (OSD) menu is activated, the #5, #11, and #13 keys are used as directional arrows to select the desired menu items and to make adjustments.

14.SOURCE

Displays the source selection bar.

10 Introduction

Image 10

BenQ MX501-V, MS500-V user manual Controls and functions, Projector

Contents

Welcome MX501/MS500/MX501-V/MS500-V Digital Projector Table of contents Refer servicing to qualified service personnel Important safety instructionsSafety Instructions Important safety instructions Safety Instructions Locations where the altitudes are higher Locations near fire alarmsLocations with an ambient temperature Confined. Allow at least 50 cm clearance Serviced InstalledIt from the power supplys power outlet Do not step on the projector or place Introduction Projector featuresIntroduction Shipping contents Projector exterior view Controls and functions Projector Remote control Pull out the battery holder Remote control effective rangeReplacing the remote control battery Operating the projector from the front Front Table Positioning your projectorChoosing a location Front Ceiling Projection dimensions Obtaining a preferred projected image size Connection Connection Terminal name Terminal appearance Connecting video source devicesConnecting audio Component Video Better Good Normal Starting up the projector OperationOperation Auto-adjusting the image Adjusting the projected imageAdjusting the projection angle Fine-tuning the image size and clarity Correcting keystone Use / to highlight the System Setup Basic menu Using the menusFollowing example describes how to set the OSD language Below is the overview of the OSD menu Setting a password Using a security cable lockUtilizing the password function Highlight Change Security Settings and press MODE/ENTER Entering the password recall procedure If you forget the passwordWrite down the number and turn off your projector Disabling the password function Switching input signalChanging the password Enter a new password Selecting the aspect ratio Magnifying and searching for detailsTo select the source About the aspect ratio Projectors native resolution in its Displayed in the centerAdjustments Screen with a 169 aspect ratio Operation Setting the User 1/User 2 mode Using Wall ColorSelecting a picture mode Go to the Picture Picture Mode menu Fine-tuning the image quality in user modes 3D Color Management Press To highlight Saturation and adjust itsEvery adjustment made will reflect to Range at 0, only pure red in the projected Count Up Increases from 0 to the preset time Count Down Setting the presentation timerTo cancel the timer, perform the following steps Selection Description Hiding the image Remote paging operationsFreezing the image Locking control keys Operating in a high altitude environment To activate the High Altitude ModeCreating your own startup screen only for MX501/ MX501-V Turning off the Power On/Off Ring Tone Adjusting the soundAdjusting the sound level Shutting down the projector Direct power off Once the cooling process finishes, a Power Off Ring Main menu Sub-menu Options Menu operationMenu system Basic Main menu Sub-menu Options System Setup Basic Advanced Description of each menu Save Settings Picture ModeTemperature Display menu Picture menu Function Description Teaching Settings System Setup Basic menu Function Description Quick AutoTimer Search Background Panel KeyLock Splash Baud Rate System Setup Advanced menu Function DescriptionReset All Test Pattern System CurrentStatus Maintenance Care of the projector Lamp information Setting Lamp Mode as EconomicSetting Auto Power Off Getting to know the lamp hour Timing of replacing the lamp Status Message Replacing the lamp Use the handle to slowly pull the lamp out Projector Resetting the lamp timer Connect the power and restart the projectorTime will be reset to Lamp events IndicatorsLight Status & Description Power events Thermal events Troubleshooting Specifications Projector specifications Dimensions Ceiling mount installation Timing chart Supported timing for PC input Timing Supported timing for Component-YPbPrinputSupported timing for Video and S-Video inputs Vertical Horizontal Copyright Warranty and Copyright informationLimited warranty Disclaimer