Using the menus, Below is the overview of the OSD menu | BenQ MS500

Using the menus

The projector is equipped with On-Screen Display (OSD) menus for making various adjustments and settings.

The OSD screenshots below are for reference only, and may differ from the actual design.

Below is the overview of the OSD menu.

Main menu icon

Main menu

DISPLAY

Wall Color

Aspect Ratio

Keystone

Sub-menu

Position

Phase

H. Size

Digital Zoom

3D Sync

3D Sync Invert

Highlight

Teaching Template

Current input signal

Analog RGB

Off

Auto

ENTER

0

0

On

Disable

MENU Exit

Status

Press MENU/ EXIT to the previous page or to exit.

The following example describes how to set the OSD language.

1.Press MENU/EXIT on the projector or remote control to turn the OSD menu on.

DISPLAY

Wall Color	Off
Aspect Ratio	Auto
Keystone
Position
Phase	0
H. Size	0
Digital Zoom
3D Sync	On
3D Sync Invert	Disable
Teaching Template
Analog RGB	MENU Exit

3.Press to highlight Language

and press / to select a preferred language.

SYSTEM SETUP: Basic

Presentation Timer
Language	English
Projector Position	Front Table
Menu Settings
Operation Settings	Front+Top
Remote Receiver	Front+Top
Panel Key Lock	Off
Background Color	BenQ
Splash Screen	BenQ
MyScreen

Analog RGB

MENU Exit

2.Use / to highlight the SYSTEM SETUP: Basic menu.

SYSTEM SETUP: Basic

Presentation Timer
Language	English
Projector Position	Front Table
Menu Settings
Operation Settings	Front+Top
Remote Receiver	Front+Top
Panel Key Lock	Off
Background Color	BenQ
Splash Screen	BenQ
MyScreen

4.Press MENU/EXIT twice* on the projector or remote control to leave and save the settings.

*The first press leads you back to the main menu and the second press closes the OSD menu.

Analog RGB	MENU Exit

20 Operation

Image 20

BenQ MS500 Using the menus, Below is the overview of the OSD menu, Following example describes how to set the OSD language

Contents

Welcome MX501/MS500/MX501-V/MS500-V Digital Projector Table of contents Important safety instructions Safety InstructionsRefer servicing to qualified service personnel Important safety instructions Safety Instructions Locations near fire alarms Locations with an ambient temperatureLocations where the altitudes are higher Confined. Allow at least 50 cm clearance Installed It from the power supplys power outletServiced Do not step on the projector or place Introduction Projector featuresIntroduction Shipping contents Projector exterior view Controls and functions Projector Remote control Remote control effective range Replacing the remote control batteryPull out the battery holder Operating the projector from the front Positioning your projector Choosing a locationFront Table Front Ceiling Projection dimensions Obtaining a preferred projected image size Connection Connection Connecting video source devices Connecting audioTerminal name Terminal appearance Component Video Better Good Normal Operation OperationStarting up the projector Adjusting the projected image Adjusting the projection angleAuto-adjusting the image Fine-tuning the image size and clarity Correcting keystone Using the menus Following example describes how to set the OSD languageUse / to highlight the System Setup Basic menu Below is the overview of the OSD menu Using a security cable lock Utilizing the password functionSetting a password Highlight Change Security Settings and press MODE/ENTER Write down the number and turn off your projector If you forget the passwordEntering the password recall procedure Switching input signal Changing the passwordDisabling the password function Enter a new password To select the source Magnifying and searching for detailsSelecting the aspect ratio Projectors native resolution in its Displayed in the center AdjustmentsAbout the aspect ratio Screen with a 169 aspect ratio Operation Using Wall Color Selecting a picture modeSetting the User 1/User 2 mode Go to the Picture Picture Mode menu Fine-tuning the image quality in user modes Press To highlight Saturation and adjust its Every adjustment made will reflect to3D Color Management Range at 0, only pure red in the projected Setting the presentation timer To cancel the timer, perform the following stepsCount Up Increases from 0 to the preset time Count Down Selection Description Remote paging operations Freezing the imageHiding the image Locking control keys Creating your own startup screen only for MX501/ MX501-V To activate the High Altitude ModeOperating in a high altitude environment Adjusting the sound Adjusting the sound levelTurning off the Power On/Off Ring Tone Shutting down the projector Direct power off Once the cooling process finishes, a Power Off Ring Menu operation Menu systemMain menu Sub-menu Options Basic Main menu Sub-menu Options System Setup Basic Advanced Description of each menu Picture Mode TemperatureSave Settings Display menu Picture menu Function Description Teaching System Setup Basic menu Function Description Quick Auto TimerSettings Search Panel Key LockBackground Splash System Setup Advanced menu Function Description Reset AllBaud Rate Test Pattern Status CurrentSystem Maintenance Care of the projector Setting Lamp Mode as Economic Setting Auto Power OffLamp information Getting to know the lamp hour Timing of replacing the lamp Status Message Replacing the lamp Use the handle to slowly pull the lamp out Projector Time will be reset to Connect the power and restart the projectorResetting the lamp timer Indicators Light Status & Description Power eventsLamp events Thermal events Troubleshooting Specifications Projector specifications Dimensions Ceiling mount installation Timing chart Supported timing for PC input Supported timing for Component-YPbPrinput Supported timing for Video and S-Video inputsTiming Vertical Horizontal Warranty and Copyright information Limited warrantyCopyright Disclaimer