Search, Presentation, Timer, Language, Projector, Menu | BenQ MS500

3. SOURCE menu

4. SYSTEM SETUP: Basic menu

	Function	Description
	Quick Auto	See "Switching input signal" on page 23 for details.
	Search	See "Switching input signal" on page 23 for details.
	Search
	Presentation	Reminds the presenter to finish the presentation within a certain time
	Timer	frame. See "Setting the presentation timer" on page 30 for details.

	Language	Sets the language for the On-Screen Display (OSD) menus. See "Using
	Language	the menus" on page 20 for details.
		the menus" on page 20 for details.

	Projector	The projector can be installed on a ceiling or behind a screen, or with
	Position	one or more mirrors. See "Choosing a location" on page 13 for details.

		Menu Display Time
		Sets the length of time the OSD will remain active after your last key
	Menu	press. The range is from 5 to 30 seconds in 5-second increments.
	Menu	Menu Position
	Settings	Menu Position
	Settings	Sets the On-Screen Display (OSD) menu position.
		Reminder Message
		Sets the reminder messages on or off.

		Direct Power On
		Allows the projector to turn on automatically once the power is fed
		through the power cord.
		Auto Power Off
		Allows the projector to turn off automatically if no input signal is
		detected after a set period of time. See "Setting Auto Power Off" on page
		45 for details.
	Operation	Quick Cooling
	Operation	Enables or disables the Quick Cooling function. Selecting On enables
	Settings	the function and projector cooling time will be shortened from a
		normal 90-second duration to approximately 30 seconds.
		Blank Timer
		Sets the image blank time when the Blank feature is activated, once
		elapsed the image will return to the screen. See "Hiding the image" on
		page 31 for details.
		Sleep Timer
		Sets the auto-shutdown timer. The timer can be set to a value between
		30 minutes and 12 hours.

40 Operation

Image 40

BenQ MS500 System Setup Basic menu Function Description Quick Auto, Search, Presentation, Timer, Language, Projector, Menu

Contents

Welcome MX501/MS500/MX501-V/MS500-V Digital Projector Table of contents Important safety instructions Safety InstructionsRefer servicing to qualified service personnel Important safety instructions Safety Instructions Locations near fire alarms Locations with an ambient temperatureLocations where the altitudes are higher Confined. Allow at least 50 cm clearance Installed It from the power supplys power outletServiced Do not step on the projector or place Introduction Projector featuresIntroduction Shipping contents Projector exterior view Controls and functions Projector Remote control Remote control effective range Replacing the remote control batteryPull out the battery holder Operating the projector from the front Positioning your projector Choosing a locationFront Table Front Ceiling Projection dimensions Obtaining a preferred projected image size Connection Connection Connecting video source devices Connecting audioTerminal name Terminal appearance Component Video Better Good Normal Starting up the projector OperationOperation Adjusting the projected image Adjusting the projection angleAuto-adjusting the image Fine-tuning the image size and clarity Correcting keystone Using the menus Following example describes how to set the OSD languageUse / to highlight the System Setup Basic menu Below is the overview of the OSD menu Using a security cable lock Utilizing the password functionSetting a password Highlight Change Security Settings and press MODE/ENTER Entering the password recall procedure If you forget the passwordWrite down the number and turn off your projector Switching input signal Changing the passwordDisabling the password function Enter a new password Selecting the aspect ratio Magnifying and searching for detailsTo select the source Projectors native resolution in its Displayed in the center AdjustmentsAbout the aspect ratio Screen with a 169 aspect ratio Operation Using Wall Color Selecting a picture modeSetting the User 1/User 2 mode Go to the Picture Picture Mode menu Fine-tuning the image quality in user modes Press To highlight Saturation and adjust its Every adjustment made will reflect to3D Color Management Range at 0, only pure red in the projected Setting the presentation timer To cancel the timer, perform the following stepsCount Up Increases from 0 to the preset time Count Down Selection Description Remote paging operations Freezing the imageHiding the image Locking control keys Operating in a high altitude environment To activate the High Altitude ModeCreating your own startup screen only for MX501/ MX501-V Adjusting the sound Adjusting the sound levelTurning off the Power On/Off Ring Tone Shutting down the projector Direct power off Once the cooling process finishes, a Power Off Ring Menu operation Menu systemMain menu Sub-menu Options Basic Main menu Sub-menu Options System Setup Basic Advanced Description of each menu Picture Mode TemperatureSave Settings Display menu Picture menu Function Description Teaching System Setup Basic menu Function Description Quick Auto TimerSettings Search Panel Key LockBackground Splash System Setup Advanced menu Function Description Reset AllBaud Rate Test Pattern System CurrentStatus Maintenance Care of the projector Setting Lamp Mode as Economic Setting Auto Power OffLamp information Getting to know the lamp hour Timing of replacing the lamp Status Message Replacing the lamp Use the handle to slowly pull the lamp out Projector Resetting the lamp timer Connect the power and restart the projectorTime will be reset to Indicators Light Status & Description Power eventsLamp events Thermal events Troubleshooting Specifications Projector specifications Dimensions Ceiling mount installation Timing chart Supported timing for PC input Supported timing for Component-YPbPrinput Supported timing for Video and S-Video inputsTiming Vertical Horizontal Warranty and Copyright information Limited warrantyCopyright Disclaimer