Menu operation, Menu system, Basic | BenQ MS500-V, MX501-V manual

Menu operation

Menu system

Please note that the on-screen display (OSD) menus vary according to the signal type selected and the projector model you are using.

Main menu Sub-menu			Options

	Wall Color		Off/Light Yellow/Pink/Light
	Wall Color		Green/Blue/Blackboard
			Green/Blue/Blackboard
	Aspect Ratio		Auto/Real/4:3/16:9/16:10
	Keystone
	Position
1.	Phase
1.	H. Size
DISPLAY
DISPLAY	Digital Zoom
	3D Sync		Frame Sequential/Off
	3D Sync Invert		Disable/Invert
	Teaching	Blackboard	Off/Letter Formation/Worksheet/
	Template (only	Blackboard	Coordinate Chart
	Template (only		Coordinate Chart
	for MX501/	Whiteboard	Off/Letter Formation/Worksheet/
	MX501-V)	Whiteboard	Coordinate Chart
	MX501-V)		Coordinate Chart
	Picture Mode	Dynamic/Presentation/sRGB/Cinema/User 1/User 2

Reference Mode Dynamic/Presentation/sRGB/Cinema

Brightness

Contrast

Color

Tint

2.Sharpness

PICTURE
PICTURE	Brilliant Color		On/Off
	Color Temperature		Cool/Normal/Warm
		Primary Color	R/G/B/C/M/Y
	3D Color	Hue
	Management	Saturation
		Gain
	Save Settings
3. SOURCE Quick Auto Search			On/Off

		Timer Period	1~240 minutes
		Timer Display	Always/1 min/2 min/3 min/Never
4.		Timer Position	Top-Left/Bottom-Left/Top-Right/
SYSTEM	Presentation		Bottom-Right
SYSTEM	Presentation	Timer Counting
SETUP:	Timer	Timer Counting	Count Down/Count Up
Basic		Direction
Basic		Sound	On/Off
		Reminder	On/Off
		Reminder

On/Off

Operation 35

Image 35

BenQ MS500-V, MX501-V user manual Menu operation, Menu system, Main menu Sub-menu Options, Basic

Contents

MX501/MS500/MX501-V/MS500-V Digital Projector Welcome Table of contents Important safety instructions Important safety instructionsSafety Instructions Refer servicing to qualified service personnel Safety Instructions Confined. Allow at least 50 cm clearance Locations near fire alarmsLocations with an ambient temperature Locations where the altitudes are higher Do not step on the projector or place InstalledIt from the power supplys power outlet Serviced Introduction Projector featuresIntroduction Shipping contents Projector exterior view Projector Controls and functions Remote control Operating the projector from the front Remote control effective rangeReplacing the remote control battery Pull out the battery holder Front Ceiling Positioning your projectorChoosing a location Front Table Obtaining a preferred projected image size Projection dimensions Connection Connection Component Video Better Good Normal Connecting video source devicesConnecting audio Terminal name Terminal appearance Operation OperationStarting up the projector Fine-tuning the image size and clarity Adjusting the projected imageAdjusting the projection angle Auto-adjusting the image Correcting keystone Below is the overview of the OSD menu Using the menusFollowing example describes how to set the OSD language Use / to highlight the System Setup Basic menu Highlight Change Security Settings and press MODE/ENTER Using a security cable lockUtilizing the password function Setting a password Write down the number and turn off your projector If you forget the passwordEntering the password recall procedure Enter a new password Switching input signalChanging the password Disabling the password function To select the source Magnifying and searching for detailsSelecting the aspect ratio Screen with a 169 aspect ratio Projectors native resolution in its Displayed in the centerAdjustments About the aspect ratio Operation Go to the Picture Picture Mode menu Using Wall ColorSelecting a picture mode Setting the User 1/User 2 mode Fine-tuning the image quality in user modes Range at 0, only pure red in the projected Press To highlight Saturation and adjust itsEvery adjustment made will reflect to 3D Color Management Selection Description Setting the presentation timerTo cancel the timer, perform the following steps Count Up Increases from 0 to the preset time Count Down Locking control keys Remote paging operationsFreezing the image Hiding the image Creating your own startup screen only for MX501/ MX501-V To activate the High Altitude ModeOperating in a high altitude environment Shutting down the projector Adjusting the soundAdjusting the sound level Turning off the Power On/Off Ring Tone Once the cooling process finishes, a Power Off Ring Direct power off Basic Menu operationMenu system Main menu Sub-menu Options Main menu Sub-menu Options System Setup Basic Advanced Description of each menu Display menu Picture menu Function Description Teaching Picture ModeTemperature Save Settings Search System Setup Basic menu Function Description Quick AutoTimer Settings Splash Panel KeyLock Background Test Pattern System Setup Advanced menu Function DescriptionReset All Baud Rate Status CurrentSystem Care of the projector Maintenance Getting to know the lamp hour Setting Lamp Mode as EconomicSetting Auto Power Off Lamp information Status Message Timing of replacing the lamp Replacing the lamp Use the handle to slowly pull the lamp out Projector Time will be reset to Connect the power and restart the projectorResetting the lamp timer Thermal events IndicatorsLight Status & Description Power events Lamp events Troubleshooting Projector specifications Specifications Ceiling mount installation Dimensions Supported timing for PC input Timing chart Vertical Horizontal Supported timing for Component-YPbPrinputSupported timing for Video and S-Video inputs Timing Disclaimer Warranty and Copyright informationLimited warranty Copyright