Manuals / BenQ / Computer Equipment / Projector

BenQ MX511 user manual INFORMATION menu

Models: MX511

1 70

Download 70 pages 14.12 Kb

Page 54

Image 54

6. INFORMATION menu

FUNCTION

(default setting/ DESCRIPTION (default setting/value) value)

	FAQ-Image
	and
	Installation	Displays possible solutions to problems you may encounter.

	FAQ-
	FAQ-
	Features and
	Service

		Source
		Shows the current signal source.
		Picture Mode
		Shows the selected mode in the PICTURE menu.
	Current	Resolution
	Current	Shows the native resolution of the input signal.
	System	Color System
	Status	Color System
	Status	Shows input system format, NTSC, PAL, SECAM, or RGB.
		Shows input system format, NTSC, PAL, SECAM, or RGB.
		Equivalent Lamp Hour
		Displays the number of hours the lamp has been used.
		Firmware Version
		Shows firmware version.

54 Operation

Page 54

Image 54

Contents

MS510/MX511 Digital Projector User Manual WelcomePositioning your projector14 Table of contentsImportant safety Warranty and Copyright3. Refer servicing to qualified service personnel Important safety instructionsSafety Instructions operate your projector. Save it forSafety Instructions Continued 4 Important safety instructionsSafety Instructions Continued 13. Do not place this projector in any of the following environmentsSafety Instructions Continued 6 Important safety instructionsProjector features IntroductionShipping contents Standard accessoriesOptional accessories Projector exterior view Front/upper sideSee Projector on page 10 for 3. LAMP indicator light Controls and functionsProjector 6. Mode/EnterCeiling mounting the projector 7. Volume + Remote control1. II Power See Using the menus on page 27 for details16. Timer Setup Replacing the remote control battery15. Timer On See Setting the presentation timer onSet Front Ceiling in the SYSTEM SETUP Basic Positioning your projectorChoosing a location Set Rear Table in the SYSTEM SETUP Basic ProjectorObtaining a preferred projected image size Positioning your projectorHow to determine the recommended screen size for a given distance Diagonal Projection dimensionsScreen size Max lengthConnection Connecting a monitor Connecting a computer or monitorConnecting a computer To connect the projector to a notebook or desktop computername Connecting Video source devicesConnecting audio HDMIConnecting an HDMI source device To connect the projector to an HDMI source deviceConnecting a Component Video source device To connect the projector to a Component Video source deviceConnecting an S-Video/composite source device To connect the projector to an S-Video/Video source deviceOperation Starting up the projectorAuto-adjusting the image Adjusting the projected imageAdjusting the projection angle horizontal angleFine-tuning the image size and clarity Correcting keystoneUsing the menus 2. Use / to highlight the SYSTEM SETUP Basic menuSetting a password Using a security cable lockUtilizing the password function If you forget the passwordDisabling the password function Entering the password recall procedureChanging the password 2. Press Mode/Enter. The message INPUT CURRENT PASSWORD displays30 Operation Switching input signal Changing Color SpaceMagnifying and searching for details Selecting the aspect ratio32 Operation About the aspect ratio Optimizing the image Selecting a picture modeSetting the User 1/User 2 mode 2. Go to the PICTURE Picture Mode menuAdjusting Brightness Using Wall ColorFine-tuning the image quality in user modes Adjusting Contrast3D Color Management About color temperatures2. Press Mode/Enter and the 3D Color Management page displays Creating your own startup screen 3. A confirmation message displays. Press CAPTURE or Mode/Enter againPresentation Timer page Setting the presentation timerTo cancel the timer, perform the following steps Increases from 0 to the preset timeHow to use the Timer On key? Remote paging operationsHiding the image Utilizing FAQ function Freezing the imageto highlight the INFORMATION menu Operating in a high altitude environment Adjusting the soundAdjusting the sound level To activate the High Altitude Mode1. Press II Power and a confirmation message displays prompting you Personalizing the projector menu displayShutting down the projector If you dont respond in a few seconds, the message will disappearMain menu Menu operationMenu system Sub-menu4. SYSTEM SETUP Basic 44 OperationAdvanced SETUPSYSTEM INFORMATIdefault setting Description of each menuDESCRIPTION default setting/value not white. See Using Wall Color on page 35 for detailsdefault setting/ DESCRIPTION default setting/value value For a PC type signalFUNCTION picture mode on page 34 for details DESCRIPTION default setting/valuedefault setting SeeAdjusting Contrast on page 35 for detailsSee Switching input signal on page 31 for details See Adjusting Brilliant Color on page 35 for detailsSee Selecting a Color Temperature on page 35 for details Adjusts white peaking while maintaining correct color presentationTimer position Timer periodTimer display Timer counting directionDirect Power On Change password Lamp modeReset lamp timer Change Security Settingsdefault setting Closed Caption EnableDESCRIPTION default setting/value FUNCTION6. INFORMATION menu Cleaning the projector case MaintenanceCleaning the lens Care of the projectorLamp information Setting Lamp mode as EconomicSetting Auto Power Off Getting to know the lamp hourStatus Timing of replacing the lampSetting Lamp mode as Economic on page MessageReplacing the lamp 2. Loosen the screw on the lamp coverprojector and b lifting it off Resetting the lamp timer Power events IndicatorsPOWER LightThe password is incorrect TroubleshootingRemote control does not work The projector does not turn onElectrical SpecificationsOptical MechanicalCeiling mount screws DimensionsCeiling mount installation Unit mmTiming chart Supported timing for PC inputSupported timing for HDMI input 66 SpecificationsSupported timing for Component-YPbPr input Supported timing for Video and S-Video inputsColor sub-carrier Copyright Warranty and Copyright informationLimited warranty DisclaimerEEC statement for European users Regulation statementsFCC statement WEEE directiveAccessibility Requirements for Rehabilitation Act of 1973, Section 70 Regulation statements