Turning the projector off, Power II or OFF again | BenQ SH940

Turning the projector off

To turn the projector off, press POWER ( II ) on the projector or OFF on the remote control and a warning message appears. Press

POWER ( II ) or OFF again.

•The Power indicator light flashes orange and the fans run for about two minutes to cool the lamp. The projector will not respond to any commands until the cooling process is complete.

•Then, the Power indicator light is a steady orange once the cooling process has finished and fans stop.

•If the projector will not be used for an extended period, unplug the power cable from the power outlet.

•To protect the lamp, the projector will not respond to any commands during the cooling process.

• Lamp life results will vary depending on environmental conditions and usage.

•If you attempt to re-start the projector shortly after shutdown,

the fans may run for a few minutes to cool down. Press II Power again to start the projector after the fans stop and the Power indicator light turns orange.

English

Using the projector

41

Image 41

BenQ SH940 user manual Turning the projector off, Power II or OFF again

Contents

SH940 Digital Projector Table of contents Important safety instructions Important safety instructions Disposal Moisture condensationAvoid volatile liquids Overview Shipping contents Ceiling mounting the projector Remote control batteriesRemote control operation Projector features Front and upper side view Projector exterior viewRear view Under view Control panel Controls and functions Remote control Choosing a location Positioning your projector Obtaining a preferred projected image size Installation for a 169 ratio screen Projection dimensions Floor Installation Ceiling Installation Installation for a 43 ratio screenScreen dimensions Projection distance D Lowest Highest Screen aspect ratio is 43 and the projected picture is To use the lens shift lever Shifting the projection lens Preparations Connecting with video equipmentConnecting Hdmi devices Connecting video devices Connecting component-video/RGB devices Connecting a monitor Connecting a computer Preparations Using the projectorTurning the projector on Changing Color Space Using the OSD menuSelecting an input source Securing the projector Using the menusUsing a security cable lock If you forget the password Utilizing the password functionSetting a password Disabling the password function Entering the password recall procedureChanging the password Adjusting the projection angle Adjusting the projected imageAuto-adjusting the image Fine-tuning the image size and clarity Correcting picture distortion Selecting a preset mode Using the preset and user modesFine-tuning the selected picture mode To fine-tune the picture mode Resetting the picture mode Setting the User 1/User 2 modeTo reset the picture mode to the preset factory values Renaming user modes Fine-tuning the picture quality Selecting a color temperature Setting Black LevelAdvanced picture quality controls Controlling image clarity Selecting a Gamma setting Setting a preferred color temperatureAdjusting Brilliant Color To set a preferred color temperature Color Management Setting Film Mode About the aspect ratio Setting 3D Comb FilterSelecting the aspect ratio Using Panamorph lenses optional Freezing the image Hiding the image Adjusting the sound quality Adjusting the soundTurning off the Power On/Off Ring Tone Muting the sound Controlling the projector through a Lan environment Configuring the Lan Control SettingsControlling the projector remotely through a web browser If you are in a Dhcp environment Enter Operating in a high altitude environment To activate High Altitude Mode To display the PIP window Displaying more than one image source simultaneously Turning the projector off Power II or OFF again On-Screen Display OSD structure On-Screen Display OSD menusPicture Basic System SetupDisplay Dhcp Information Resolution Load Settings Picture ModeReset Picture Settings YPbPr Tuning AdjustmentBlank Timer Display menu Menu Settings System Setup menuLanguage Splash Screen Closed Caption Closed Caption EnableStandby Monitor Out Lamp Settings Advanced Setup menuHdmi Settings Audio Settings Information menu ResolutionSource Equivalent Lamp Care of the projector Additional information Setting Auto Power Off Setting Lamp Power as EconomicLamp information Getting to know the lamp hour Status Message Timing of replacing the lampReplacing the lamp English Resetting the lamp timer Light Status & Description IndicatorsPower events Problem Cause Remedy Troubleshooting General characteristics SpecificationsOptical Electrical Ceiling mount installation Dimensions Supported timing for PC input Timing chartFormat Refresh rate Format Resolution Refresh rate Freq. KHz Pixel Freq MHz Format Resolution Refresh rate Hz Freq. KHz Pixel Freq. MHzSupported timing for Hdmi Hdcp input Supported timing for Edtv and Hdtv via Component inputs Warranty Warranty and Copyright informationCopyright Disclaimer