Factory Default Settings | Billion Electric Company 6404VGP, 6404VP

Factory Default Settings

VoIP/(802.11g) Broadband Firewall Router

Factory Default Settings

Before configuring your, you need to know the following default settings.

Web Interface (Username and Password)

Username: admin

Password: admin

The default username and password are “admin” and “admin” respectively.

	If you ever forget the username/password to login to the router, you may
	press the RESET button up to 6 seconds to restore the factory default
	settings.
A	Caution: After pressing the RESET button for more than 6 seconds, to be sure you power
A	cycle the device again.
Attention

Device LAN IP settings:

IP Address: 192.168.1.254

Subnet Mask: 255.255.255.0

ISP setting in WAN site:

PPPoE

DHCP server

DHCP server is enabled.

Start IP Address: 192.168.1.100

IP pool counts: 100

LAN and WAN Port Addresses

The parameters of LAN and WAN ports are pre-set in the factory. The default values are shown below.


		LAN Port


	IP address	192.168.1.254
	Subnet Mask	255.255.255.0
	DHCP server function	Enabled
	IP addresses for	100 IP addresses continuing from
	distribution to PCs	192.168.1.100 through 192.168.1.199

WAN Port

The PPPoE function is enabled to automatically get the WAN port configuration from the ISP.

16

Chapter 3: Basic Installation

Image 17

Billion Electric Company 6404VGP Factory Default Settings, Web Interface Username and Password, Device LAN IP settings

Contents

VoIP/802.11g Broadband Firewall Router BiPAC 6404VP / 6404VGPUser’s Manual Version Release 5.08a Table of Contents QoS Quality of Service Firewall and Access ControlCHAPTER 5 TROUBLESHOOTING VoIP Voice over Internet Protocol Chapter 1 Introduction FeaturesIntroduction to your Router 802.11g Wireless AP with WPA Support Dynamic Host Configuration Protocol DHCP client and server Quality of Service QoSNetwork Address Translation NAT SOHO Firewall Security with DoS and SPI Rich Management Interfaces Firmware Upgradeable Important note for using this router Chapter 2 Installing the RouterPackage Contents Do not use the same power source for this router as other equipment RJ-45 connector The Front LEDsWireless Router Only RJ-11 connector Port Power Switch PWR RESET The Rear PortsWAN LAN Phone 1X Cabling Chapter 3 Basic Installation Chapter 3 Basic Installation ATA Mode Broadband Router Mode Connecting Your Router 4. Select Internet Protocol TCP/IP and click Properties. See Figure Configuring PCs in Windows in Window XP2. Double-click Local Area Connection. See Figure 4. Select Internet Protocol TCP/IP and click Properties See Figure Configuring PCs in Windows2. Double-click Local Area “LAN” Connection. See Figure 3. Click Properties Configuring PC in Windows 95/98/ME5. Then select the DNS Configuration tab. See Figure 2. Select TCP/IP Protocol and click Properties. See Figure Configuring PC in Windows NT4.0 Web Interface Username and Password Factory Default SettingsDevice LAN IP settings ISP setting in WAN site PPPoE Information from your ISPDHCP Obtain an IP Address Automatically Static IP Fixed IP Address Configuring with your Web Browser ATA / Router Mode Configuration Chapter 4 ConfigurationSave Config to FLASH Status Status Wireless Association Table Wireless Router OnlyARP Table Routing Table RIP Routing Table DHCP TableLeased Table Expired Table VoIP Status Email Status Event Log Error Log NAT Sessions Diagnostic UPnP Portmap ATA / Router Mode LAN NAT DHCP Server Device IP WAN System Firewall QoS Virtual Server FunctionsTime Schedule Advanced VoIP Router LAN Local Area Network ConfigurationEthernet Primary IP Address IP Alias Ethernet Client Filter → Active PC in LANEthernet Client Filter Default setting is set to Disable Active PC in LAN displays a list of individual Ethernet device’s IP Address & MAC Address which connecting to the router Parameters Wireless Wireless Router Only Wireless Distribution System WDS WPA-PSK TKIP / WPA-PSK AES Pre-Shared Key Wireless Security Wireless Router OnlyPage →Associated Wireless Clients Wireless Client / MAC Address Filter Wireless Router OnlyWireless Client Filter Default setting is set to Disable DHCP Server Time Zone System Remote Access Firmware Upgrade Backup / Restore Restart Router User Management Firewall and Access Control General Settings Packet Filter Table 1 Predefined Port Filter Example Predefined Port Filters RulesApplication Protocol UDP17 Packet Filter - Add TCP/UDP Filter Packet Filter - Add Raw IP Filter Page Click Add TCP/UDP Filter Click DeleteExample Configuring Packet Filter 5. The new port filter rule for HTTP is shown below Block Duration Intrusion Detection Intrusion Name Table 2 Hacker attack types recognized by the IDSDetect Parameter Ascend Kill Always On URL Filter dropped IM / P2P Blocking Instant Message Blocking The default is set to DisabledPeer to Peer Blocking The default is set to Disabled Log information can be seen in the Status - Event Log after enabling Firewall Log VoIP Broadband Firewall Router VoIP Voice over Internet Protocol Voice QoS Setting for Phone PortWizard NOTE User defined profiles are limited to 8 only Authentication Username Same as Phone NumberUser-defined Profiles SIP Device Parameters Advanced - Parameters How to register to SIP Server Note ONHOOK means hung up Advanced - PSTN Environment Adjustment Phone Port Login Account Configuration Volume Control For examplesCodec Preference Speed Dial PSTN Dial Plan 3 Dial at Timeout PSTN Dial Plan Examples4 Dial at Timeout no Prefix 1 Dial with Prefix VoIP/802.11g Broadband Firewall Router VoIP Dial Plan Prefix Processing Dial Plan Rules List Description Dial-Plan ExamplesSpecial Dial Plan Examples ## xx Localcheap.com is the default VoIP provider I set on phone port 1. When I call out any number start with 1 or 2 or 3 and plus rest of the phone number for local call, 03 is always prepended in front of these number. If 23295 are dialed, 03-2-32935 is the actual phone number called out via localcheap.com provider Mobilecheap.com is the default VoIP provider I set on phone port 2. When I call out 123-39-45678 for a mobile call, 123 is replaced with 09. Therefore, 09-39-45678 is the actual phone number called out via Mobilecheap.com provider Country Specific Ring & Tone Ring & ToneRing Parameters Tone Parameters Flash-hook Special Dial CodesOption Click Clear QoS Quality of ServicePrioritization High DSCP Mapping Table Table 4 DSCP Mapping TableWireless Router Device Standard DSCP Outbound IP Throttling LAN to WAN Inbound IP Throttling WAN to LAN Connection Diagram VoIP Normal PCs Restricted PCInformation and Settings Example QoS for your Network Mission-critical application Advanced setting by using IP throttlingVoice application Restricted Application VoIP/802.11g Broadband Firewall Router Virtual Server “Port Forwarding” Internal IP Add Virtual Server IP Address Example Edit DMZ Host Global IP Address Edit One-to-One NAT Network Address Translation Select the Apply button to apply your changes Example List of some well-known and registered port numbers Table 5 Well-known and registered PortsPort Number Protocol Time Schedule Configuration of Time Schedule Click EditEdit a Time Slot Delete a Time Slot Management and IGMP Static Route Advanced Dynamic DNS Check Email Embedded Web Server 2 Management IP accounts Device Management SNMP V1 and Universal Plug and Play UPnPSNMP SNMP Version SNMPv2c and SNMPv3 From RFC 1493 Bridge MIB From RFC1650 EtherLike-MIBFrom RFC 1471 PPP/LCP MIB From RFC 1472 PPP/Security MIB IGMP Save Configuration to FlashLogout Problems starting up the router Chapter 5 TroubleshootingProblems with the LAN Interface Problem Contact Billion WORLDWIDE APPENDIX A Product Support and Contact Information