Ring & Tone, Ring Parameters | Billion Electric Company 6404VGP

Ring & Tone

VoIP Broadband Firewall Router

Ring & Tone

This section allows advanced user to change the existing or newly defined parameters for the various ring tones (dial tone, busy tone, answer tone and etc.)

Country Specific Ring & Tone

Region: Select a country ring-tone, from the drop-down list, where you are located. This VoIP router provides default parameter of ring tones according to different countries. The ring-tone parameters are automatically displayed after entering a specific country. If your country is not in the list, you may manually create ring-tone parameters.

Ring Parameters

Ring Cadence (in ms): Ring cadence is defined by three fields, Frequency: On Time1, Off Time1, On Time2, Off Time2 and On Time3, Off Time3. Frequency is specified in Hertz. Time is given in milliseconds.

Tone Parameters

You may need to check with your local telephone service provider for such information. Also, it is recommended that this option be configured by an advanced user, unless you are instructed to do so.

Click Apply to apply the settings.

76

Chapter 4: Configuration

Image 77

Billion Electric Company 6404VGP, 6404VP user manual Country Specific Ring & Tone, Ring Parameters, Tone Parameters

Contents

VoIP/802.11g Broadband Firewall Router BiPAC 6404VP / 6404VGPUser’s Manual Version Release 5.08a Table of Contents QoS Quality of Service Firewall and Access ControlCHAPTER 5 TROUBLESHOOTING VoIP Voice over Internet Protocol Chapter 1 Introduction FeaturesIntroduction to your Router 802.11g Wireless AP with WPA Support Dynamic Host Configuration Protocol DHCP client and server Quality of Service QoSNetwork Address Translation NAT SOHO Firewall Security with DoS and SPI Rich Management Interfaces Firmware Upgradeable Important note for using this router Chapter 2 Installing the RouterPackage Contents Do not use the same power source for this router as other equipment RJ-45 connector The Front LEDsWireless Router Only RJ-11 connector Port Power Switch PWR RESET The Rear PortsWAN LAN Phone 1X Cabling Chapter 3 Basic Installation Chapter 3 Basic Installation ATA Mode Broadband Router Mode Connecting Your Router 4. Select Internet Protocol TCP/IP and click Properties. See Figure Configuring PCs in Windows in Window XP2. Double-click Local Area Connection. See Figure 4. Select Internet Protocol TCP/IP and click Properties See Figure Configuring PCs in Windows2. Double-click Local Area “LAN” Connection. See Figure 3. Click Properties Configuring PC in Windows 95/98/ME5. Then select the DNS Configuration tab. See Figure 2. Select TCP/IP Protocol and click Properties. See Figure Configuring PC in Windows NT4.0 Web Interface Username and Password Factory Default SettingsDevice LAN IP settings ISP setting in WAN site PPPoE Information from your ISPDHCP Obtain an IP Address Automatically Static IP Fixed IP Address Configuring with your Web Browser ATA / Router Mode Configuration Chapter 4 ConfigurationSave Config to FLASH Status Status Wireless Association Table Wireless Router OnlyARP Table Routing Table RIP Routing Table DHCP TableLeased Table Expired Table VoIP Status Email Status Event Log Error Log NAT Sessions Diagnostic UPnP Portmap ATA / Router Mode LAN NAT DHCP Server Device IP WAN System Firewall QoS Virtual Server FunctionsTime Schedule Advanced VoIP Router LAN Local Area Network ConfigurationEthernet Primary IP Address IP Alias Ethernet Client Filter → Active PC in LANEthernet Client Filter Default setting is set to Disable Active PC in LAN displays a list of individual Ethernet device’s IP Address & MAC Address which connecting to the router Parameters Wireless Wireless Router Only Wireless Distribution System WDS WPA-PSK TKIP / WPA-PSK AES Pre-Shared Key Wireless Security Wireless Router OnlyPage →Associated Wireless Clients Wireless Client / MAC Address Filter Wireless Router OnlyWireless Client Filter Default setting is set to Disable DHCP Server Time Zone System Remote Access Firmware Upgrade Backup / Restore Restart Router User Management Firewall and Access Control General Settings Packet Filter Table 1 Predefined Port Filter Example Predefined Port Filters RulesApplication Protocol UDP17 Packet Filter - Add TCP/UDP Filter Packet Filter - Add Raw IP Filter Page Click Add TCP/UDP Filter Click DeleteExample Configuring Packet Filter 5. The new port filter rule for HTTP is shown below Block Duration Intrusion Detection Intrusion Name Table 2 Hacker attack types recognized by the IDSDetect Parameter Ascend Kill Always On URL Filter dropped IM / P2P Blocking Instant Message Blocking The default is set to DisabledPeer to Peer Blocking The default is set to Disabled Log information can be seen in the Status - Event Log after enabling Firewall Log VoIP Broadband Firewall Router VoIP Voice over Internet Protocol Voice QoS Setting for Phone PortWizard NOTE User defined profiles are limited to 8 only Authentication Username Same as Phone NumberUser-defined Profiles SIP Device Parameters Advanced - Parameters How to register to SIP Server Note ONHOOK means hung up Advanced - PSTN Environment Adjustment Phone Port Login Account Configuration Volume Control For examplesCodec Preference Speed Dial PSTN Dial Plan 3 Dial at Timeout PSTN Dial Plan Examples4 Dial at Timeout no Prefix 1 Dial with Prefix VoIP/802.11g Broadband Firewall Router VoIP Dial Plan Prefix Processing Dial Plan Rules List Description Dial-Plan ExamplesSpecial Dial Plan Examples ## xx Localcheap.com is the default VoIP provider I set on phone port 1. When I call out any number start with 1 or 2 or 3 and plus rest of the phone number for local call, 03 is always prepended in front of these number. If 23295 are dialed, 03-2-32935 is the actual phone number called out via localcheap.com provider Mobilecheap.com is the default VoIP provider I set on phone port 2. When I call out 123-39-45678 for a mobile call, 123 is replaced with 09. Therefore, 09-39-45678 is the actual phone number called out via Mobilecheap.com provider Country Specific Ring & Tone Ring & ToneRing Parameters Tone Parameters Flash-hook Special Dial CodesOption Click Clear QoS Quality of ServicePrioritization High DSCP Mapping Table Table 4 DSCP Mapping TableWireless Router Device Standard DSCP Outbound IP Throttling LAN to WAN Inbound IP Throttling WAN to LAN Connection Diagram VoIP Normal PCs Restricted PCInformation and Settings Example QoS for your Network Mission-critical application Advanced setting by using IP throttlingVoice application Restricted Application VoIP/802.11g Broadband Firewall Router Virtual Server “Port Forwarding” Internal IP Add Virtual Server IP Address Example Edit DMZ Host Global IP Address Edit One-to-One NAT Network Address Translation Select the Apply button to apply your changes Example List of some well-known and registered port numbers Table 5 Well-known and registered PortsPort Number Protocol Time Schedule Configuration of Time Schedule Click EditEdit a Time Slot Delete a Time Slot Management and IGMP Static Route Advanced Dynamic DNS Check Email Embedded Web Server 2 Management IP accounts Device Management SNMP V1 and Universal Plug and Play UPnPSNMP SNMP Version SNMPv2c and SNMPv3 From RFC 1493 Bridge MIB From RFC1650 EtherLike-MIBFrom RFC 1471 PPP/LCP MIB From RFC 1472 PPP/Security MIB IGMP Save Configuration to FlashLogout Problems starting up the router Chapter 5 TroubleshootingProblems with the LAN Interface Problem Contact Billion WORLDWIDE APPENDIX A Product Support and Contact Information