Mission-critical application | Billion Electric Company 6404VP

Mission-critical application

VoIP/(802.11g) Broadband Firewall Router

Mission-critical application

Mostly the VPN connection is mission-critical application for doing data exchange between head and branch office.

The mission-critical application must be sent out smoothly without any dropping. Set priority as high level for preventing any other applications to saturate the bandwidth.

Voice application

Voice is latency-sensitive application. Most VoIP devices are use SIP protocol and the port number will be assigned by SIP module automatically. Better to use fixed IP address for catching VoIP packets as high priority.

Above settings will help to improve quality of your VoIP service when traffic is full loading.

Restricted Application

Some of companies will setup FTP server for customer downloading or home user sharing their files by using FTP.

With above settings that help to limit utilization of upstream of FTP. Time schedule also help you to only limit utilization at daytime.

Advanced setting by using IP throttling

With IP throttling you can specify more detail for allocating bandwidth; even the applications are located in the same level.

Upstream: 928kbps (29*32kbps)

Mission-critical Application: 192kbps (6*32kbps)

Voice Application: 128kbps (4*32kbps)

Restricted Application: 160kbps (5*32kbps)

Other Applications: 448kbps (14*32kbps)

6+4+14+5=29, 29*32kbps=928kbps

83

Chapter 4: Configuration

Image 84

Billion Electric Company 6404VP, 6404VGP user manual Mission-critical application, Voice application, Restricted Application

Contents

BiPAC 6404VP / 6404VGP VoIP/802.11g Broadband Firewall RouterUser’s Manual Version Release 5.08a Table of Contents Firewall and Access Control QoS Quality of ServiceCHAPTER 5 TROUBLESHOOTING VoIP Voice over Internet Protocol Features Chapter 1 IntroductionIntroduction to your Router 802.11g Wireless AP with WPA Support Quality of Service QoS Dynamic Host Configuration Protocol DHCP client and serverNetwork Address Translation NAT SOHO Firewall Security with DoS and SPI Firmware Upgradeable Rich Management Interfaces Chapter 2 Installing the Router Important note for using this routerPackage Contents Do not use the same power source for this router as other equipment The Front LEDs RJ-45 connectorWireless Router Only RJ-11 connector The Rear Ports Port Power Switch PWR RESETWAN LAN Phone 1X Cabling Chapter 3 Basic Installation Chapter 3 Basic Installation Connecting Your Router ATA Mode Broadband Router Mode Configuring PCs in Windows in Window XP 2. Double-click Local Area Connection. See Figure4. Select Internet Protocol TCP/IP and click Properties. See Figure Configuring PCs in Windows 2. Double-click Local Area “LAN” Connection. See Figure4. Select Internet Protocol TCP/IP and click Properties See Figure Configuring PC in Windows 95/98/ME 5. Then select the DNS Configuration tab. See Figure3. Click Properties Configuring PC in Windows NT4.0 2. Select TCP/IP Protocol and click Properties. See Figure Factory Default Settings Web Interface Username and PasswordDevice LAN IP settings ISP setting in WAN site Information from your ISP DHCP Obtain an IP Address Automatically Static IP Fixed IP AddressPPPoE Configuring with your Web Browser Chapter 4 Configuration ATA / Router Mode ConfigurationSave Config to FLASH Status Wireless Association Table Wireless Router Only StatusARP Table Routing Table DHCP Table RIP Routing TableLeased Table Expired Table Email Status VoIP Status Error Log Event Log Diagnostic NAT Sessions UPnP Portmap ATA / Router Mode Functions LAN NAT DHCP Server Device IP WAN System Firewall QoS Virtual ServerTime Schedule Advanced VoIP Router Configuration LAN Local Area NetworkEthernet Primary IP Address IP Alias → Active PC in LAN Ethernet Client Filter Default setting is set to DisableEthernet Client Filter Active PC in LAN displays a list of individual Ethernet device’s IP Address & MAC Address which connecting to the router Wireless Wireless Router Only Parameters Wireless Distribution System WDS Wireless Security Wireless Router Only WPA-PSK TKIP / WPA-PSK AES Pre-Shared KeyPage Wireless Client / MAC Address Filter Wireless Router Only Wireless Client Filter Default setting is set to Disable→Associated Wireless Clients DHCP Server System Time Zone Remote Access Firmware Upgrade Backup / Restore Restart Router User Management Firewall and Access Control General Settings Packet Filter Example Predefined Port Filters Rules Table 1 Predefined Port FilterApplication Protocol UDP17 Packet Filter - Add TCP/UDP Filter Packet Filter - Add Raw IP Filter Page Click Delete Click Add TCP/UDP FilterExample Configuring Packet Filter 5. The new port filter rule for HTTP is shown below Intrusion Detection Block Duration Table 2 Hacker attack types recognized by the IDS Intrusion NameDetect Parameter Ascend Kill URL Filter Always On dropped Instant Message Blocking The default is set to Disabled Peer to Peer Blocking The default is set to DisabledIM / P2P Blocking Firewall Log Log information can be seen in the Status - Event Log after enabling VoIP Voice over Internet Protocol VoIP Broadband Firewall Router Setting for Phone Port WizardVoice QoS Authentication Username Same as Phone Number User-defined ProfilesNOTE User defined profiles are limited to 8 only SIP Device Parameters How to register to SIP Server Advanced - Parameters Advanced - PSTN Environment Adjustment Note ONHOOK means hung up Login Account Configuration Phone Port For examples Volume ControlCodec Preference Speed Dial PSTN Dial Plan PSTN Dial Plan Examples 3 Dial at Timeout4 Dial at Timeout no Prefix 1 Dial with Prefix Chapter 4 Configuration VoIP Dial Plan Dial Plan Rules List Prefix Processing Dial-Plan Examples DescriptionSpecial Dial Plan Examples ## xx Localcheap.com is the default VoIP provider I set on phone port 1. When I call out any number start with 1 or 2 or 3 and plus rest of the phone number for local call, 03 is always prepended in front of these number. If 23295 are dialed, 03-2-32935 is the actual phone number called out via localcheap.com provider Mobilecheap.com is the default VoIP provider I set on phone port 2. When I call out 123-39-45678 for a mobile call, 123 is replaced with 09. Therefore, 09-39-45678 is the actual phone number called out via Mobilecheap.com provider Ring & Tone Country Specific Ring & ToneRing Parameters Tone Parameters Special Dial Codes OptionFlash-hook QoS Quality of Service Click ClearPrioritization High Table 4 DSCP Mapping Table DSCP Mapping TableWireless Router Device Standard DSCP Outbound IP Throttling LAN to WAN Inbound IP Throttling WAN to LAN VoIP Normal PCs Restricted PC Connection DiagramInformation and Settings Example QoS for your Network Advanced setting by using IP throttling Mission-critical applicationVoice application Restricted Application Chapter 4 Configuration Virtual Server “Port Forwarding” Add Virtual Server Internal IP Example IP Address Edit DMZ Host Edit One-to-One NAT Network Address Translation Global IP Address Select the Apply button to apply your changes Table 5 Well-known and registered Ports Example List of some well-known and registered port numbersPort Number Protocol Time Schedule Click Edit Configuration of Time ScheduleEdit a Time Slot Delete a Time Slot Advanced Management and IGMP Static Route Dynamic DNS Check Email Device Management Embedded Web Server 2 Management IP accounts Universal Plug and Play UPnP SNMP V1 andSNMP SNMP Version SNMPv2c and SNMPv3 From RFC1650 EtherLike-MIB From RFC 1493 Bridge MIBFrom RFC 1471 PPP/LCP MIB From RFC 1472 PPP/Security MIB Save Configuration to Flash LogoutIGMP Chapter 5 Troubleshooting Problems starting up the routerProblems with the LAN Interface Problem APPENDIX A Product Support and Contact Information Contact Billion WORLDWIDE