sketch B if a properly grounded outlet is not available. The temporary adapter should be used only until a properly grounded outlet can be installed by a qualified electrician. The
ADAPTER SHOWN IN FIGURES B & C IS NOT FOR USE IN CANADA.
Extension Cords
Tools that have 3 wire cords requiring grounding must only be used with extension cords that have 3- prong grounding type plugs and
An extension cord must have adequate wire size (AWG or American Wire Gauge) for safety, and to prevent loss of power and overheating. The smaller the gauge number of the wire, the greater the capacity of the cable, that is 16 gauge has more capacity than 18 gauge. When using more than one extension to make up the total length, be sure each individual extension contains at least the mini- mum wire size. To determine the minimum wire size required, refer to the following chart:
120 VOLT TOOLS: CHART FOR MINIMUM WIRE SIZE (AWG) OF EXTENSION CORDS
Cord Length (feet) 25 | 50 | 75 | 100 |
Guage:16 14 12 10
Before using an extension cord, inspect it for loose or exposed wires, damaged insulation, and defective fittings. Make any needed repairs or replace the cord if necessary. B&D has extension cords available that are U.L. (C.S.A. in Canada) listed for outdoor use.
Unpacking Your Saw
Check the contents of your miter saw carton to make sure that you have received all parts. In addition to this instruction manual, the carton should contain: one 3680 miter saw, one carbide saw blade and one blade wrench in wrench pocket.
Familiarization
Your miter saw is fully assembled in the carton. Open the box and lift the saw out by the convenient carrying handle, as shown in Figure 1. Place the saw on a smooth, flat surface such as a workbench or
strong table. Examine Figures on inside front cover of this manual to become familiar with the saw | ||
and its various parts. The following section on adjust- |
| |
ments will refer to these terms and you must know what |
| |
the parts are. |
| |
Press down lightly on the operating handle and pull out |
| |
the lock down pin, as shown in Figure 2. Gently release |
| |
the downward pressure and allow the arm to rise to its |
| |
full height. Use the lock down pin when carrying the saw |
| |
from one place to another. Always use the carrying han- | Figure 1 | |
dle or the hand indentations to transport the saw. | ||
| ||
ADJUSTMENT AND SET UP
Specifications
Capacity of cut
48˚ miter left and right | 0˚ miter |
| |
48˚ bevel left: 3˚ right |
| Max. Height 3.9" | Result Width 5.9" |
|
| Max. Width 7.9" | Result Height 2.5" |
45˚ miter |
| 45˚ bevel |
|
Max. Height 3.9" | Result Width 4.1" | Max. Height 2.7” | Result Width 5.9” |
Max. Width 5.5" | Result Height 2.5" | Max Width 7.9” | Result Height 1.7” |
Drive
2000 Watts out 13 Amp Motor
Cut Helical Gears with Ball Bearings Carbide Blade, 4000 RPM Automatic Electric Brake
Bench Mounting
Holes are provided in all four feet to facilitate bench mounting. (Two different sized holes are provided to accommodate different sizes of screws. Use either hole, it is not necessary to use both.) Always mount your saw firmly to prevent movement. To enhance the tool’s portability, it can be mounted to a piece of 1/2” or thicker plywood which can then be clamped to your work support or moved to other job sites and reclamped.
NOTE: If you elect to mount your saw to a piece of plywood, make sure that the mounting screws don’t protrude from the bottom of the wood. The plywood must sit flush on the work support. When clamping the saw to any work surface, clamp only on the clamping bosses where the mounting screw holes are located. Clamping at any other point will surely interfere with the proper operation of the saw.
CAUTION: To prevent binding and inaccuracy, be sure the mounting surface is not warped or other- wise uneven. If the saw rocks on the surface, place a thin piece of material under one saw foot until the saw sits firmly on the mounting surface.
Figure 2 |
| Figure 3 |
|
|
|
|
|
|
LOCK DOWN
PIN
GUARD BRACKET
SCREW
3
