Symbols |
|
|
|
|
| • Kickback, Rotational - The rapid upward and backward motion | |||||
The label on your tool may include the following symbols. |
| of the saw which can occur when the moving saw chain near the | |||||||||
The symbols and their definitions are as follows: |
| upper portion of the tip of the guide bar contacts an object, such as | |||||||||
V................. volts | A........... amperes |
| a log or branch. | ||||||||
Hz............... hertz | W.......... watts |
| • |
| |||||||
min............. minutes |
|
|
| ........ alternating current |
| performance requirements of ANSI | |||||
|
|
|
| ........... direct current | no......... no load speed |
| representative sample of chain saws.) | ||||
|
|
|
|
| • Normal Cutting Position - Those positions assumed in | ||||||
|
|
| ............... Class I Construction |
|
|
| ......... earthing terminal |
| |||
|
|
|
|
|
|
| performing the bucking and felling cuts. | ||||
|
|
|
|
|
|
| |||||
|
|
|
|
|
|
| |||||
|
|
|
|
|
|
| |||||
|
|
|
| (grounded) |
|
|
| ....... safety alert symbol |
| • | Reduced Kickback Guide Bar - A guide bar which has been |
|
|
| ............... Class II Construction | .../min or rpm...revolutions or |
| demonstrated to reduce kickback significantly. | |||||
|
|
|
| (double insulated) |
|
|
| reciprocation per minute |
| • | Replacement Saw Chain - A chain that complies with kickback |
|
|
|
|
|
|
|
|
|
| performance requirements of ANSI | |
|
|
|
| CHAIN SAW NAMES AND TERMS |
| with specific chain saws. It may not meet the ANSI performance | |||||
|
|
|
|
|
|
|
|
|
| requirements when used with other saws. | |
• Bucking - The process of cross cutting a felled tree or log into lengths. |
| ||||||||||
| • | Saw Chain - A loop of chain having cutting teeth, that cut the | |||||||||
• Chain Brake - A device used to stop the chain saw. |
| wood and that is driven by the motor and is supported by the guide bar. | |||||||||
• Chain Saw Powerhead - A chain saw without the saw chain and |
| • | Switch - A device that when operated will complete or interrupt an | ||||||||
guide bar. |
|
|
|
|
| electrical power circuit to the motor of the chain saw. | |||||
• Clutch - A mechanism for connecting and disconnecting a driven |
| • | Switch Linkage - The mechanism that transmits motion from a | ||||||||
member to and from a rotating source of power. |
| trigger to the switch. | |||||||||
• Drive Sprocket or Sprocket - The toothed part that drives the |
|
|
| ||||||||
saw chain. |
|
|
|
|
|
| important safety instructions for | ||||
• Felling - The process of cutting down a tree. |
|
| battery chargers | ||||||||
• Felling Back Cut - The final cut in a tree felling operation made on |
|
|
| ||||||||
| SAVE THESE INSTRUCTIONS: This manual contains important | ||||||||||
the opposite side of the tree from the notching cut. |
| ||||||||||
• Guide Bar - A solid railed structure that supports and guides the saw chain. |
| safety instructions for battery chargers. | |||||||||
• Kickback - The backward or upward motion, or both of the guide |
| • Before using charger, read all instructions and cautionary markings | |||||||||
bar occurring when the saw chain near the nose of the top area of |
|
| on charger, battery pack, and product using battery pack. | ||||||||
the guide bar contacts any object such as a log or branch, or when |
|
| WARNING: Shock hazard. Do not allow any liquid to get inside charger. | ||||||||
the wood closes in and pinches the saw chain in the cut. |
|
| CAUTION: Burn hazard. To reduce the risk of injury, charge | ||||||||
• Kickback, Pinch - The rapid pushback of the saw which can |
| only designated Black & Decker batteries. Other types of batteries | |||||||||
occur when the wood closes in and pinches the moving saw chain |
| may burst causing personal injury and damage. | |||||||||
|
| CAUTION: Under certain conditions, with the charger plugged | |||||||||
in the cut along the top of the guide bar. | 6 |
| in to the power supply, the charger can be shorted by foreign | ||||||||
|
|
|
|
|
|
|
|
|
|
| |
