CC880/LP880, SC8016 Operators Guide 5.0 | Disarming the System |
|
|
EN 9
How to Arm the System in STAY Mode 2
Hold down the [0] button until two beeps are heard. The STAY indicator displays and exit time starts counting.
Any zones programmed to be automatically isolated in STAY Mode 2 flash until exit time expires. At the end of exit time, all zones selected to be automatically isolated turn off and the codepad gives one short beep.
4.5Programming STAY Mode 2 Zones
Programming zones to be automatically isolated in STAY Mode 2 are only carried out if you have a master code.
How to Program STAY Mode 2 Zones
1.Enter your four character master code, followed by [8] and the [#] button (for example,
[2 5 8 0 8 #]). Three beeps are heard and the STAY indicator flashes.
2.Enter the zone number to be automatically isolated, followed by the [*] button (for example, [1 *] = Zone 1, [2 *] = Zone 2).
The selected zone flashes. If you make a mistake, enter the same zone number followed by the [#] button to clear the incorrect zone.
To select additional zones to be automatically isolated in STAY Mode 2, repeat Step 2 as many times as required.
3.To exit this mode, press the [#] button when you have selected all zones to be automatically isolated in STAY Mode 2. Two beeps are heard and the STAY and AWAY indicators turn off.
5.0 Disarming the System
When you enter the premises after the system is armed in AWAY Mode, or if you armed the system in STAY Mode 1 or STAY Mode 2, you must disarm the system before entry time expires to disable detection devices that activate an alarm.
If there was an alarm condition prior to disarming the system, a flashing zone indicator displays, indicating a previous alarm on that zone.
How to Disarm the System
Enter your user code followed by the [#] button (for example, [2 5 8 0 #]). Two beeps are heard.
6.0 Adding User Codes
Only the master code holder can add or change other system user codes, including two auxiliary codes and the master code. The master code is factory default is User 1; however, multiple user codes can be assigned to be a master code. Up to 32 user codes can be programmed to operate the system. User code 33 and user code 34 are auxiliary codes only.
How to Add a User Code
1.Enter your four character master code, followed by [1] and the [#] button (for example,
[2 5 8 0 1 #]).
Three beeps are heard and the STAY and AWAY indicators flash.
2.Enter the user code number (1 to 34), followed by the [#] button (for example, [2 #] = User 2, [3 3 #] = Auxiliary Code 1). Two beeps are heard and the selected user number displays on the codepad indicators.
3.Enter the digits (up to seven digits) required for the new code followed by the [#] button (for example, for user code 5768, enter [5 7 6 8 #]). Two beeps are heard and the STAY and AWAY indicators turn off.
To add or change other user codes, repeat this procedure as many times as required.
7.0Deleting User Codes
Only the master code holder can delete other system user codes and auxiliary code 1 and 2.
How to Delete a User Code
1.Enter your four character master code, followed by [1] and the [#] button (for example,
[2 5 8 0 1 #]).
Three beeps are heard and the STAY and AWAY indicators flash.
2.Enter the user code number (1 to 34), followed by the [#] button (for example, [2 #] = User 2, [3 3 #] = Auxiliary Code 1). Two beeps are heard and the selected user number displays on the codepad indicators.
3.Press the [*] button to delete the selected user code.
Two beeps are heard and the STAY and AWAY indicators turn off.
To delete other user codes, repeat this procedure as many times as required.
Bosch Security Systems 6/04 920036O.OG.162
