Bosch Appliances D2071A Function Keys, Data Keys, Tones, Editing a Record, Programmer Connection

D2071A Operations & Installation Guide 3.0 Programming

3.2Function Keys

Table 7 identifies the six function keys that simplify using the programmer.

Table 7: Function Keys

Key		Use
	ON	Key switch that turns on the programmer.
		Does not power down the programmer. Turn
		off by selecting 5200 OFF in the Product
		Handlers Menu. Powers down automatically
		after the programmed Time Out time elapses.
HELP		Switches programmer into Help Mode. Refer
		to the D5200 Programmer Operation Manual
		(P/N: 74-06176-000) for more information.
	CANCEL	Cancels changed items if you did not press
		[ENTER] to accept the change.
RECV		Moves a copy of the record in the attached
(COPY)		product to the D5200 Programmer.
	SEND	Moves a copy of the record in the D5200
	(LOAD)	Programmer to a product being programmed.
CLEAR		Erases an un-entered or entered program item
		data and replaces it with blank spaces.

Note: All function keys are red.

3.3Data Keys

Use the white keys on the keyboard for data entry.

3.4Tones

The D5200 Programmer emits four distinct sounds to notify users of key presses, data acceptance or rejection, and system errors (Table 8).

3.5Editing a Record

1.Scroll to the D2071 Product Handler from the Product Handlers Menu using [↑] or [↓] and press [ENTER GROUP].

2.Scroll to the appropriate record title using [↑] or [↓] ] and press [ENTER GROUP].

3.Use [↑] or [↓] to scroll to the appropriate program. Edit the entry and press [ENTER] to input the data.

4.Press [EXIT GROUP] to exit the record. The Save display appears if changes were made to any program item entries in the record.

3.6Programmer Connection

Access the four-pin programmer connector ( J3) by sliding back the D2071A’s cover. This connector is located next to Terminal 1 (refer to Figure 1 on page 7). The D2071A is ready for programming after connecting it to the programmer; it is not necessary to reset the D2071A before loading to or copying from the panel.

Table 8:			Tones
	Sound		Signifies
	Click		Short, sharp tone that occurs each time you
			press a key. The programmer does not click
			when you press [ON], [CAP LOCK], and
			[SHIFT].
	Pip		Short, single frequency tone sounds when you
			press [ENTER] and the D5200 accepts the
			change.
	Tweedle		Quick series of pips indicating you pressed an
			invalid key or made an inappropriate entry.
	Buzz		Flat tone indicating a system error. Examples of
			typical system errors are:
			• A product is not connected to the D5200
			when you attempt to copy or load it.
			• The D5200 notifies you of a low battery
			condition.
			• The D5200 announces it will automatically
			count down and turn off.
			• You are attempting to delete a record or
			handler.
			• You are entering into a product handler
			containing a Timeout Save Record. The
			Timeout Save Record was saved by the
			D5200 when it automatically turned off to
			save power.
		Programming before installing the phone
		lines might sound the buzzer.

You can program the D2071A before installation. If the D2071A is powered and not connected to a telephone line, the Phone Fail Buzzer sounds after approximately 10 min. Power down the unit to silence the buzzer.

Program the D2071A using the D5200 Programmer with the D2071 Product Handler.

Before programming, read and become familiar with this section of the Operation and Installation Guide.

3.7Entering the 2071 Handler

1.At the Product Handler Level, press [↓] and scroll down to 2071.

2.Press [ENTER GROUP].

3.When the cursor appears on the NEWRECORD prompt, press [ENTER GROUP].

Account# appears.

Bosch 09/04 74-06200-000-F 1 9